Jump to content
SAU Community

Recommended Posts

Have a 97 RS4 here that was wrapped round a pole by look of it.

I bought it to use parts for my wifes stagea I just bought..so no floor mats cargo net and cover as all in my stagea along with a few other bits and peices and possibly bonnet

Front end still good though guards have some dents

Has 101k's on clock

All completely standard no mods at all.

Let me know what you need and i'll send photos prices etc

Starting from $5.00

Located in Sydney

can email me airtech354 at hotmail dot com or PM me

Tks

Daniel.

post-3004-1276141031_thumb.jpg

post-3004-1276141042_thumb.jpg

post-3004-1276141053_thumb.jpg

post-3004-1276141060_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/324314-wrecking-97-rs4/
Share on other sites

Holy shit! Nasty smash...

I'm after the seat release handle surround in the boot, passenger side I'm pretty sure

posted to Adelaide

thanks sav

not wrong!!

$20 posted just confirm side for me if want it

Tks

Daniel.

Link to comment
https://www.sau.com.au/forums/topic/324314-wrecking-97-rs4/#findComment-5285769
Share on other sites

im after the plastic cargo barrier roof clip that sits right at the back drivers side..if is it grey and how much to post to vic

not sure if i have it i'll get a photo let me know if part you mean

Link to comment
https://www.sau.com.au/forums/topic/324314-wrecking-97-rs4/#findComment-5293019
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...