Jump to content
SAU Community

Recommended Posts

So its a black JZZ30 manual black interior soarer.

mod list is....

Engine

1JZ 2.5Ltr straight 6

garrett gt3076r .82 ballbearing turbo (Brand New 2 weeks old)

stainless steel manifold

apexi 50mm wastegate with screamer

braided oil and water lines with speed flow fittings

custom dump pipe

blitz Nur spec stainless exhaust with silencer for the street

Pod filter

750cc injectors

Fmic with custom piping

Fuel System

2 x bosch 040 external fuel pumps with speed flow fittings

2L surge tank

Sard fuel pressure regulator

Electricial

Greddy emanage blue ecu

Greddy E01 boost controller

Blitz carbon faced boost guage and saber water temp guage

Suspension

tein ha coilovers (no noises or knocks)

Race Prepped Wheel Alignment (new arms)

Body

factory v8 front bar

Vertex side skirts

Vertex rear bar

Vented f-glass bonnet + ill also inc the std metal bonnet too, its in excellent condition.

Drive line

Locked diff with 4.1 gears

R154 gearbox 5 speed gearbox

Quater master hudraulic custom release bearing kit

With a custom built NPC clutch to mine and dougs specs!! Plus i will also chuck in the Orc super single clutch..

Wheels are a 17x9.5 +20 5 spoke with deep dish (black center) with a 15mm bolt on..

I have done the water pump in it, the timing belt has been done also the belt tensoiner has been replaced too, ah also i have the tanks removed on the radiator and cleaned up so it never gets hot, i also have a water squirter system rigged in it too, just in case.

the car also has 6 moths rego

Cd player plus 6x9s in the doors plus 6 inch speakers in the back..

Ac compressor is new and has just been re gassed so its ober cold!!

Tint all round and lolly pop steering wheel.

So the car is located on the Gold Coast/.

Im asking 12,500 for a quick sale..THE ONLY SWAP IM INTERESTED IN IS A R34

call me on 0412 898 772

115 000ks on the clock and 430rw hp

post-74544-0-76774400-1313718581_thumb.jpg

post-74544-0-69494700-1313718585_thumb.jpg

post-74544-0-71020200-1313718590_thumb.jpg

post-74544-0-76905600-1313718595_thumb.jpg

post-74544-0-13206500-1313718607_thumb.jpg

post-74544-0-83087600-1313718614_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/374554-euges-soarer/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...