Jump to content
SAU Community

Recommended Posts

Cleaned out the garage yesterday, found some gear that needs a new home.

IMG_1230_zps9c66d184.jpg

RB25 S1 Throttle position sensor
$10

IMG_1239_zps107a0208.jpg

Offset rack spacer
14x1.5mm (R33/S14/S15/R34 etc)
$15

IMG_1242_zps528389a6.jpg

7 row oil cooler
New
$50

gallery_1619_111_194984.jpg

RB25 AN10 rocker cover fittings (these aren't push in, will need sealant/weld to keep them in) They might be RB20 (unsure if they have smaller holes)
$20

Stagea-WGNC34.jpg

Nissan Stagea S1 RS4 grille includes Stagea double unicorn badge
$50

sensor_zpsd4a35f7c.jpg

G Sensor
Out of Stagea, should be same as GTR
$120

cable_zps673236c0.jpg

S15 throttle cable
perfect for Skylines with forward facing plenums
$60

atessa_zpsf9aa2cd5.jpg

ATTESA pump
out of Stagea, should be same as GTR
$150

diff_zpscade037e.jpg

R34 open diff centre (accepts both 3x2 and 5x1 I'm selling below)
perfect to weld up and shizzz
$60

photo11_zps91769b6a.jpg

3x2 half shafts
Off Stagea
ABS
$60

photo-2_zps85791ba0.jpg

5x1 half shafts
Off R34
$60

teinsprings_zpsb4d7ff34.jpg

Tein springs

Specs:

70mm ID 6kg spring rate
2x 225mm long
2x 250mm long

$50 pair $80 set
I've gotten too many PM's whether they'll fit certian cars, I don't know. Measure your current springs internal diameter (ID).

IMG_2288.jpg

Chargespeed eyelids for Stagea
Brand new, black ABS platsic
$100 shipped (currently in Japan)

Will add more stuff as I find it.

Located in Liverpool, will ship at buyers expense.

Adam.

Edited by Run-It-Hard
Link to comment
https://www.sau.com.au/forums/topic/423345-nsw-random-nissan-parts-sale/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...