Jump to content
SAU Community

Recommended Posts

  • Replies 425
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Are you sure with this many loud and modded cars we are not going to be Cop bait??  :P

We'll probably have 5 cop cars following us and if so we're sitting ducks for defects...  :)

Well.. If anyone does any silly stuff, like burnouts wheel spins.. speeding..

Their number plates will be reported to the police.

Dont be stupid and do silly things

As with all Official SAU cruises; everyone has been well behaved etc. Hoonism/Heroism is treated with criticism rather than praise...

We've had cruises with such numbers many many times... I don't remember once that we've had trouble with the police.

This should be good; great work with the organization Steve - hope your car is big enough for the food, looks like you'll have a few cows in the boot :P

As with all Official SAU cruises; everyone has been well behaved etc.  Hoonism/Heroism is treated with criticism rather than praise...

We've had cruises with such numbers many many times...  I don't remember once that we've had trouble with the police.

This should be good; great work with the organization Steve - hope your car is big enough for the food, looks like you'll have a few cows in the boot :P

Thanks stan, yeah one whole cow just for me

And yes, seeing as it wont be Australia Day the cops shouldnt be an issue

"Hoonism" will not be tolerated. Simple. By that i mean no burnouts, donuts etc.

The last spot we will most likely see police is the turnoff to the National Park (where they SOMETIMES do a radar gun speed trap).

List updated (again)

Are you sure with this many loud and modded cars we are not going to be Cop bait??  :P

We'll probably have 5 cop cars following us and if so we're sitting ducks for defects...  :D

I dont have you on the list - r u going?

Are you sure with this many loud and modded cars we are not going to be Cop bait??  :P

We'll probably have 5 cop cars following us and if so we're sitting ducks for defects...  :)

we have done cruises with large amounts of cars many times and no hassell from the cops. dont act stupid and they will leave us alone. :)

would it be a good idea to give some directions to P6 for folks that haven't ever been there.

Like where to turn off from Homebush Bay drive... How far up Dawn Fraser do we go (hope not too far... *shudder*).

I've just been looking @ whereis.com and can't find the parking areas.

Cheers

would it be a good idea to give some directions to P6 for folks that haven't ever been there.

Like where to turn off from Homebush Bay drive...  How far up Dawn Fraser do we go (hope not too far... *shudder*).

I've just been looking @ whereis.com and can't find the parking areas.

Cheers

Heres a (crappy) map showing p6, and the second map shows the directions from Homebush Bay Drive

Once you get near P6 you shouldnt miss all the skylines there - it wont exactly be subtle

Hope it helps

Map_for_P6.bmp

Map_for_p6_from_m_road.bmp




  • Similar Content

  • Latest Posts

    • The ATTESSA is functionally identical to R34; there were a bunch of JDM models that continued ATTESSA including Fuga/Q70, Skyline/Q50, Cima etc as an option. All with Auto only and I think mostly for snow regions. AFAIK there were no AWD VR30DDTT sold in Australia - it is on my to do list to check regs for racing a LHD car in Targa/ATR/AASA/CAMS events because if I can get the auto to work it would be interesting to run a 4wd car The Ecuteck TCM tuning is the same model as their ECU tuning, they already have it for R35 and Dose's favourite, BMW. You buy "points" to allow your computer to be tuned, buy either a bluetooth (phone app) or bluetooth+USB+Key (phone and PC) dongle, and pay for a tune that will be locked to your tuner ( ). You can also access the tuning software yourself but 1. it is mega expensive and 2. these computers have a billion parameters that intersect, so how could you ever spend enough time on it to get a decent result.
    • Or, is it a case of what it is like owning an R series Skyline? NFI what the previous owner has done or fiddled with... Ha ha ha After reading through this thread, I went on a bit of a research about the Q50/Q60. Now I'm quite intrigued by them! Is the AWD in them more like a WRX where it's always AWD, or is it more like the ATTESSA in the GTRs? By the sound of this TCU tuning, this sounds like a case of someone has made some real software for it, and you just need the right piece of hardware, and then you license that specific vehicle/TCU. Or is this a case of the software will be really expensive so only a few tuners have it, and you still have to pay a license per vehicle?
    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
×
×
  • Create New...