[v36 windscreen]

Anyone replaced a windscreen? is there a local equivalent? I just coped a rock through mine

[Skyline v36 coupe (370gt) ls1]

ls1 converted 370gt coupe, engine is cammed & maf-less tuned, custom headers & full exhaust, huge ally rad xyz coilovers.  Looks and sounds like porn, goes like stink. Mod plated 6months reg & rwc $25k

[Trust twin turbo kit complete kit $2700]

I have a full twin td05-16g trust turbo kit, includes manifold, wastegate, turbos, dump pipes, twin entry intercooler, cold side piping, twin greddy BOV's all silicone joiners etc made over 400rwkw on stock engine.  Will come with spare turbos and rear housings too.

[Wtb C34 S1 Rb25 Engine. Brisbane Qld But May Travel]

I have a short engine suit rebuild PM if interested

[Wtb R33 Gtr Diff Centre]

I got one pm your offer complete centre Perfect condition.

[Bride Leather Seat With Rail]

Location?

[Rack End/tie Rod End Interchangeability]

NIS-48520-23U26 is tie rod ends

[S1 Build. Need Opinions To Make A Decision!]

I did mine 8 years ago no problem I also used just car first then switched to Shannon's, FYI in QLD a mod plate is like an engineers report anyway it means all mods are approved for road use. I did a 4g63t swap into a proton GTI around the same time no issue's there either because its fully covered on the mod plate. Just get the report done if that's what you need in your state, because you are using factory parts you shouldn't have any trouble.

[S1 Build. Need Opinions To Make A Decision!]

Well I have an rb30/26 manual converted s1 fully insured in QLD (Shannon's) and legal engine # changed and mod plated. Not hard at all but I did it years ago no emission test required when I did the conversion.

[My Exhaust C34]

Yes it is

[Subframe Bushes For Stageas....]

Gtst bushes are the correct length GTR are too long

[Trust Twin Rb26 Td06 20G Setup $2000]

This is a f#cking bargain, I have this setup with Trust turbos and 600kw is easy do you have dumps? I would buy this for spares if I had a lasy 2k

[Wanted Dirt Cheap C34 Stagea]

Thinking about it..have you got something?

Might be interested in a bare fornt cut too to fix the shell I found

Turns out modification rules have changed in the last 2 weeks

Car now needs to be a complied car, so import with no complaince is not an option or a stat writeoff

Been thinking about dropping a wagon onto a GU patrol frame. I thought they wanted chassis # only too didn't know of the rule change.

[spot the stagea]

What looked like a green (it was dark) s1 at greenbank tonight

So after 8 years of ownership I may have been spotted woot woot

[Wanted Dirt Cheap C34 Stagea]

What are you doing 4wd ute?

[Rb25Det Neo Full Rebuild $?]

What an epic waste of money. I just built a neo for less than 3k with a similar power figure target. I just started an rb30/25 build with the same target power figure, this will cost below 3k including awd adaptor. IMHO I would never bother with anything other than an rb30 when its going in a Stagea. You must have your doubts thats why you made the post, so I suggest shopping around and supply all the parts. Some of the machining being quoted implies the engine is stripped and has been measured, has it? if not the you are being quoted for shit you may not need or even get.

[Rb25Det 95-97 Stagea Engine Loom]

Ok here is what I would do.

• I would not buy anything
  
• I would use the rb20 harness
  
• I would use the rb20 ecu
  
• I would get a nistune board
  
• I would be glad I did all the above
  

Now its not that easy but it is the Best solution and will give the best result. Do some research on the above because you are taking the wrong direction using a stagea harness & ecu.

[Rb25Det 95-97 Stagea Engine Loom]

Take it to an experienced auto elec for the conversion, you don't know enough to do it and there are too many cowboys here that think they know.

[Rb25Det 95-97 Stagea Engine Loom]

I would modify your harness to run the rb25

[In Tank Lift Pump To Support 6-800 Rwhp]

Stock pump will be fine as a lift pump no need to upgrade later, just make sure the rest of your system is up to scratch.

[In Tank Lift Pump To Support 6-800 Rwhp]

The stock pump should be ok just hard wire it.

[Advice On The Gt-Four And Gt-T]

They are 5 stud

[R34 Intake Pipe Help]

i see, yeah there is a black rubber boot thing that goes over it ! thats thing is pretty jamed on there so i didnt think you would not have it unless someone went to the trouble of prying it off lol.going to have to find a subsitute like above posts says shouldnt be to hard.

Thanks mate I think I have found one to buy 2nd hand, fyi I bought my car in pieces and this along with many other things was missing.

Cheers

[Advice On The Gt-Four And Gt-T]

Don't the GTt brakes bolt straight in?

Yes bolt in easy and mine came with them allready done.

[R34 Intake Pipe Help]

im going to take a guess on what your asking, but the pipe goes over the throttle body and a metal ring with a screw goes over the pipe to hold it in place.

My question is do I just clamp the plastic pipe to the throttle body? it looks like there should be a rubber boot between pipe & throttle body. The plastic pipe wont create a seal over the throttle body too so somethings got to got there and I dont have it.