[Mini Overhaul Of My R33 - Gone Wrong :(]

Missfire wont be the cause of your engine damage

[Oil And Missfire Issue]

Afm keeps getting oil on it, need to clean out the intercooler and all the piping and figure out why the oil is getting there

[S2 Rb25Det Cas , Rebuild Or Replace ?]

I had my z32 cas rebuilt by AFIin lidcombe when it died, cost about $200 from memory, looks identical to the mitsubishi rb25 one

[Shed Prices And Questions]

Have you considered polished concrete over paint?

[R35Gtr Wheels?]

im pretty sure you would be able to find someone to swap your rears for a pair of fronts, maybe with cash your way

[M35 Or Legnum.]

im in the market for a wagon, and was wondering what you guys consider a m35 has over legnum, being that thy are a few more$, but newer.

advantages of a legnum that i can see are

manual

ayc

200kw is an exhaust and remap away

lighter

cheaper

fuel economy?

the stageas seem to have a few reliability issues(cas, afm?)

i see a few of you guys have owned both and want toknow the pros and cons,

thanks

[Strengthening A Rb26 Block]

just sit it on the tray of a truck ann let he diesel idle do the job

[Arp Rb26 Head Studs (202-4207): Following Torquing Procedure Of Nisssan Or Arp?]

is the hread pitch on either end of the stud different, if so(i think they are)torquingto nissan specs with lubricant will increase the headgasket crush by about 50%

[$$ Spun Rod Bearing In Fully Built Rb30 :(]

coffee or cranks lol

[$$ Spun Rod Bearing In Fully Built Rb30 :(]

IMO the mains dont look great, but its hard to tell from pics, the fact all the big ends are trashed points to oil issues, could there be contaminants in the cooler etc? have you asked rips? Theres not somthing funny like oil thermostat or oil filter block incorrectly plumbed? how do the cams look?

[R34 Has No Spark After Being Crashed, Looking For Coil Pack Amps]

they are built into the coil(igniter) on ther34

[Rb26 Snapped Cam!]

or for a really fast test, when you remove the cam, put straight ege across the cam followers, a bent valve will show up as increased clearance

[Rb26 Compression Test No6 Very Low All 175 No6 Is 110]

most likely broken ringland

[Block Work -]

are you sure you need the head ported, what turbo and power are you hoping to run?

[The 10g Gtr Thread]

should be PAR "engineering"

[Rb25 Neo Build With Water/meth & No Intercooler]

please enlighten me , hat happens to oil? i buy 205 litre drums which last 2 years, would you not use it?

[R34 Or Supra]

do you need a boot or back seat ever?

[Possible Vct Damage - How To Test Vct Operation?]

or you can fire the cam with a timing light to see if it moves

[Gps Navigation Devices - What Do U Reccomend?]

i prefer the tomtom to my garmin, the garminchanges the scaling on the map as you drive which can be confusing

[Going From Sard 550Cc To Deka 80Lb, How To Adjust Powerfc]

try setting inj at -30, and see how it runs

[Going From Sard 550Cc To Deka 80Lb, How To Adjust Powerfc]

what injector and latency settings are in it now?

[Rb25 Neo Build With Water/meth & No Intercooler]

unfortunately loosing the fmic wont make any real difference to the rpm boost threashold, just to lag, i wouldnt expect a gtx35r to come close to a gt3076r, when they are worse than a gt35r. Imo spend the money on a hta 3076 with a good setup manifold/gate etc, probably the most responsive 500rwhp you will get, need e85 or wmi though

[Possible Head Replacement!?]

time for $100 rb30

[Neo Head Or Not?]

have you considered using the head that you already have , just build a new bottom end and swap the head once the motor is out

[New Rods And Pistons]

i would figure out whats wrong with the old motor before ordering anything