mgb2002

Wheel Manufacturer,Model: Ultralite, ATEC-II (Same as Rush Shadow Silver) Diameter: 18 Width F,R: 8.5, 9.5 Offset F,R: +27, +35 Tyre size F,R: 235/40R18, 265/35R18

First off, you have inspired me to start on my own gtt as well... so a couple of questions: - Did you sand off the top layer (that sticky stuff ) of the R34 center console, or did you put the vinyl directly on top (without preparation of the plastic)? - Does this vinyl work the same way as tinting your windows? - Could you write a very simple DIY in like 4 steps (apply, heat, wrub out airbubbles?) Thnx!

You can order the rubber end directly in japan if you wish...japanparts.com It is nissan productnumber 65820AA400 (nr 6 in the above pic), but you also might want to buy the retainer (62298AA400 for the rubber and retainer)...

Not quite sure, will have a look tonight. Again; just contact 666DAN on this forum. He has all the right led's in stock and won't rip you off

As requested (supplied by Dan)

Just contact 666DAN, he will supply you with full led kits, suited for your skyline...

Does the front bumper support bar (nr. 7 in the first pic) fit the R34 GT-T headlights? Retainer-front bumper, upper, 62240AA400 Is the distance between the headlights the same for the GT-T and GT-R? Should I be able to use this bar instead of the East-Bear Sports GTS-R spec 2 front bumper support bar?

Searched the topics ("R34 rubber") but they are all about tyres. Question: Are all the front bumper rubber-ends the same on all R34 GT-R's (all years)? According to Nissan Fast the partnumber is: Rubber-end, 65820AA400 But looking at photo's they do not look all the same Or is it just me? Can someone confirm this is the right Nissan partnumber 65820AA400 (the same rubber as the black gt-r above has between the headlights?)?

Thnx guys! Already found the info in the Sticky (step 4). Knew I have seen that one before, should have looked better.

Has anyone replaced/used bigger/better speaker cables instead of the standard factory ones in their R34 GTT? I'm going to use a 4-channel amp from the boot and run the cables from there using the passenger side to the front speakers. (The power cable from the battery and the remote cable will be run through the drivers side.) The factory wiring is usually not the best quality, so I'd like to replace them with better ones. Can they be run through the factory connector in the door? Is there enough room in the connectors to run extra wires? Or do I have to make an extra hole in the door to run the new cables trough?

I have been looking into this also and found two more systems: - HKS CAMP2. http://www.hksusa.com/info/?id=3474 - Magden Automotive M.1b Performance Computer (As seen in the new Fast & Furious movie in the blue R34 GTR) http://magden-auto.com/products/1 But both are pretty expensive systems tho...

Apexi Power Intake (not a panel filter tho )! According to this test: Induction Kit Review

Yep, thats exactly what i want the GTR Z-tune bonnet on the GTT, with the East Bear Front bumper

Yeah I know there are Z-tune bonnets for the GTT but I would like to keep the front grill in one piece. That would mean i would have to cut a part of the bonnet

Bigger picture of the kit:

Sorry for not using the search function (usually the first to tell others they have to strange ) I'm going for the East Bear Spec 2 kit from Knight-Racer, but as stated I want a different bonnet. The GTR bar from KR will fit the GTT wings. NZMO thank you for the part numbers. Is the locking mechanism easy to change or do you have to drill holes in the framework to fit the GTR lock? And the GTR bonnet is just as width and has the same front line (where the headlights are mounted) as the GTT bonnet?

I would like to put on a Nismo Z-tune style GT-R bonnet on a GT-T. Already getting the East Bear front, but don't like the look of their bonnet. What would I need to do this? Hinges, locking mechanism, front wings?

After browsing your forum for a while it's time to introduce myself properly. My name is Bas and I live in the south of the Netherlands. After searching the Japanese auction sites for a while I finally bought a Nissan Skyline R34 GT-T. It's a black ER34 dating from 1998 which has run about 64k km (40k miles) and with a complete history of the car. It still is a standard car, but that will soon change. I bought the car on a Japanese auction in October 2008 trough a company in Belgium, which will arrange all the paperwork etc for me. The ship from Japan arrived a couple of weeks ago in the UK, where the car was imported/registered into Europe. Now I am waiting for the car to be transported to the Netherlands to be registered here. So I will have my very own skyline in about 2 weeks hopefully (waiting for almost a half year now ). Front: Rear: Like I said the car is still completely standard. The bodykit will be the East Bear (GTS-R) kit type 2 with a GT-R spoiler.

I would like to put on a Nismo Z-tune style GT-R bonnet on a GT-T. Already getting the East Bear front, but don't like the look of their bonnet. What would I need to do this? Hinges, locking mechanism, front wings?