koduRB25det

Guys, I’m selling my 1986 Skyline R30 Manual RWD. Very rear to see this model in Australia. Original Low Km 164000 on clock. Going very cheap. Coz no need any more. Inside and outside very good [A++] in condition accept small dent on driver side door. michanically A1 condition. Options comes with, A/CPower Mirrors Power windows Power SteeringAlloy Wheels Need to attention on rear brakes with is very minor noise Rego is running out very soon. Can supply pink slip FREE of Charge. I’m asking 1100.00 without rego and can do rego for 6 months extra 600.00 call on 0421067989 or email mailto:[email protected]

Thanks mate. i might do someting else.....

Guys, Im plaining to put a rb25det gear box to my r30.[straight 6 cyl 2.4L]. and the same time im gonna upgrade the Diff front and back break system. just wonder gear box direct bolt to engine???? if any one know abt this...pls help. much appreciate. thanks

Guys, Im plaining to put a rb25det gear box to my r30.[straight 6 cyl 2.4L]. and the same time im gonna upgrade the Diff front and back break system. just wonder gear box direct bolt to engine???? if any one know abt this...pls help. much appreciate. thanks

guys, I just notice today my cam shaft pin[tiney pin on the cam shaft wich is align with CAS] brocken...at the exhaust side. if i put back CAS is it a problum. pls help thanks

I recon welsh plug too. do u know the part no for that...? thanks

mate belive me, try these steps. before u stops the car put it into N. see how u go. if it not stall that is ur Automatic Transmission. just chk ur fliud level. 100% its too low. top up with fluid in between L-H make sure to not to over fill. see how u go. if not, dont waste your time with doing crap. possible case is ur TCC Solenoid in the auto box. it is not a expenvice part. [$50-70] if u have a skill u can do it by ur self. other wise take it to good transmission repare workshop. if u in sydney PM me i will tell u where to go.

guys, i got a another prob with my car. pls help today i have notice, got a coolant leak from under the bellhousing. why is this...? Thanks

clean your AFM, AAC valve with cabi cleaner. and try. is your AUTOMATIC transmisson..? if so, 1 when it try to stall put it in to N 2 see how you feel. if u feel it want try to stall, 3 check your transmission fluid level. drive or idel until engine get warm, drive 1 2 3 and D and put in to R put in to N and leave it 1 min and check the level of the fluid. fluid level S/B in between L - H level. make sure your dipstick with no fluid bubles. if so do a transmission service. I had the same prob with my car. hope ths will help u.

Thanks mate. Girraween is very close to me. thanks again

guys, Im looking for a mechanic for do some work for my r33 gtst. any body know good one around westren sydney thanks

My r33 SI allso same. i just change the oil with motul 8100. b4 i use 0-40 castrol edge. when cold start with 0-40 it goes to 6-7-8.

you right mate. it was noisy lifter. prob fix my it self. thank u guys for ur help.

it happening while engine is at running as wel las the spining the cas.most of the time when the car starting and some times rev up as well

Thanks guys. today i chk again. I recon all marks are 100% match with cover. but the prob is still that TIC TIC noice is comming. when i advance the engine its too much. any body know any good workshop around westren sydney. thx

do u know anything abt this TIC TIC noice...?

I think so. do u have any suggetion...?

I use for Auto DEX III for eng oil Castrol EDGE 0w-40 or Motual 8100 with OEM filter. allways go for the good brand. just read "Good on Oil" topic.

I just finsh my head gasket replace. i use OEM head gasket with ARP studs. no prob going good. but i got bit confuce abt the cam timing. when i put back my cam gears i align all marks with back of the cam cover as well as the crank timing with the mark on the oil pump. when i put back the crank pulley, [0] orange mark want match with the the lover timing cover mark. and i have set the ing timing to 15 dig [useng timing light]. accoding to manual instruction. but when i put back the throttle sensor connector timing mark gos to 10 dig. one more thing, when i rotate the CAS for aject the timing i can hear bit loud noice like TIC TIC . why is that..? b4 i was not like that. pls see the photo. just wonder whats the prob..? pls help

mate, if u really dont know how to do rb25det head gasket, dont do it. it make worse. but if u really wonna do it ur self. i can guide u. coz i did my 3rd rb head gasket replace last week. any way where u locate..?

im locate at sydney - parramatta.

Thanks guys. i might fit my standed one and let u gys know.

Thanks for that. what do u think abt the back pressure of the car. how it going with peformance..? thanks

Guys, Im thnking abt my r33 gtst standed exhaust mufler fit with 3 inch turbo back after market exhaust. standed mufler got 2.5 diameter and wonna fit it to 3 inch pipe all the way from turbo. with this set up any prob...? PLEASE HELP thnaks

as NA said replace every thing. Timng belt/brake fluid,transmisson fluid or gear oil/diff oil[any thing synthetic 75-85w], coolant, water pump if possible, spark plugs. if im am u i normally change the power stering flud and all drive belts as well. when u change the timing belt chk the cam and crank seals for leaking or any abnormal condition. as well as tension pully and ideler if noicey replace it. most of the time these pullyes not last more than 100000 km.