Burrieddreamz

Issue SOLVED! thanks to SCOTTY for helping me out Code read P0037 O2 sensor on bank 1 ( 2nd one) was gone Much Appreciated!

yeah sounds like it would you be able to give me your garage address ? thanks man appreciate your help

Hi All, Just new to V series Skylines ( had couple of R33 S2 in the past) I recently bought one V35 Skyline Coupe auto with 119K Kms on clock. There is a Check engine light sign on the dash. I did a quick diagnostic mode test and found the Code P0037 When I start the car , it dies if I don't accelerate the first time. I am not sure if this is related to CEL(check engine light)? I cleaned MAF so far and getting the service done soon. do you know anyone in South East Suburbs who can help me diagnose this problem ? thanks in advance.

I just browsed every single page of this thread! Fantastic job mate , you just got yourself a fan there! Great build an Decent amount of power and looks.

alright I went into diagnostic mode and got this error code http://www.youtube.com/watch?v=nQDk10M9k4Y&feature=youtu.be Seems like its 2 long and 10 short does that means 20 ?

Hi everyone I've had some issues with R33 series II engine and wiring , so had to change the engine and found the good deal for Series 1.5 engine , wiring harness/loom and ECU. Got that done few months back and the power steering was heavy after that. Mechanic said that because the series 1.5 loom he couldn't find (One that goes to Hicas unit) , he left it as is and disconnected the hicas from boot ( blue wire) and took the bulb out from odo. When I installed that HICAS bulb in Odo , that was constantly ON. I diagnosed the HICAS that came with error 12 means no power to the HICAS Motor So I played around with series 1.5/2 rear loom under the steering column and connected the HICAS wire in the boot. The HICAS Light turned OFF. But steering wheel is still heavy. Am I now expecting the speedo wires not connected ? I haven't diagnosed that unit again. any one have had these issues? any help will be greatly appreciated I have a 1996 Skyline R33 series II with sunroof Thanks guys

I don't know how to find that out. I know this thing that Series I doesnt have HICAS but Series II has. now with my car ive recently installed Series I looms, ECU and S1 engine ( S2 harness have been pulled out) so does that mean its not connected? I heard if HICAS Is a issue it gets heavier . whats the possible solution you can think of? needs a Series I power steering parts?

okay so now Speedo is working and Power steering is still the same ! can it be a pump ? cuz one of my mate said it could be am now running Series 1 engine and series 1 looms not series II !! what can be the other issues?

Same Scenario with my car! but no probs with idle I got s2 type m r33 and engine i just got put in had only 88K on clock ( straight from the half cut) its a S1 engine had to do all the loom changes , engine etc etc. took abt 6 weeks to complete! should i put a fuel filter or just leave it ?

I think its 2 pin connectors on this one not sure if that was aftermarket I got the harness as well if someone wants it I'll give it free anyways. there weren't any spacers it was just tied to the injectors rails and took it off yestrday

Up for sale : 595 CC Siemens Injectors with Fuel Rail , RB25DET R34 NEO Motor. Installed in Aug 2011and taken off march 2012 Body Design: Pencil, composite plastic Flow rate: 595 cc/min, 57 lbs/hr at 43.5 psi Injector type: Saturated Configuration: Standard Length Fuel Nozzle: Single-hole, tiny droplet Resistance: 12.5 Ohms, high resistance Length: 3 inches, 74 mm Diameter: 16 mm O-rings: Viton, Top and bottom, 14.5 mm Part number: 109958 Will sell it for $350 (Stripping down whole neo engine ) sold splitfires , still available - Intake manifold /plenum, throttle body , head , bottom , ECU Location : Dandenong , Victoria Email / PM me

oh okay thanks for that man . so its the HICAS issue . i'll go yell at the garage guys

hi guys i just spent about 3350$ on my car got a fully stock R33 engine , harness and ecu with labour. now everything is okay except the power steering and speedo Power steering looks like doesn't work. I checked the fluids and all, everything is topped up but still that doesn't work . what it could be? before engine replacement it was all good

SOLD Please lock this thread thanks

Its still sitting at my mechanic's garage . I'll have to take them out in order to find out how big are they and what brand they are. I'll go on the weekend to pick up my car and the parts that were removed