dantheman88

as the title states Im after a clutch cover for a r32. Preferably on the gold coast, but im not too worried 0422051559

I tested the slave and it is fine. I took the gearbox off and when I moved it off a bit the clutch fork was able to move fine, but when its moved back on the fork cant move backwards at all. It feels like the clutch cover is too big or something for the bearing to move forward. Is the rb20 and rb25 clutch cover different? I was thinking maybe I have a rb25 one? cos the 20 and 25 clutches are the same as far as I know

tailshaft dropped to $100

bump. no longer need a 32 tailshaft

Thanks Ducati, I will try taking it off when i get home in a couple hours and see if it moves without the fork in the way. The fork definantly has no backward movement so maybe something with the pivot ball or thrust bearing has gone wrong

gone wrong I mean. I am starting to think my box is going to have to come off again

Yeh I have the right slave. Im using a rb20 box. The rb20 uses a push clutch which means the slave pin should be able to push the clutch fork right??? If so I think something has gone when I have put the clutch and box on cos I cant push the fork at all. it will only move towards the slave, and isnt the slave supposed to push it??

I recently put my rb20 gearbox and clutch on my rb25 and put the engine back in and now have just put my clutch slave on and tried to put the brake fluid through it using the DIY on here (bleeding the air out of each section) now I think I have done it right but my clutch pedal still doesnt have any pressure. I dont know how much movement the fork is supposed to have but when I put the slave on I had to compress the pin on it to get it in between the fork and where it sits. The only movement I can get on the fork is by by pushing it into the slave which pushes the slave pin in even more. Is it supposed to have more movement then that? I could hear when I push the fork into the slave when the clutch pedal is down it makes the clutch pedal jump. Another thing I notcied is that its hard to get the gears into place but Im not sure if thats because the gearbox doesnt have any oil in it. Would this cause this? or has something gone wrong with my clutch fork when my clutch went on? Or have I just put the fluid in wrong? This is how my slave sits normally. The fork cannot move backwards at all. is this normal?

Got a r33 tail shaft in great condition. Looking for $100. I need a good condition R32 tailshaft so I am willing to swap Located on the Gold Coast 0422051559

coilpacks sold. Also got a 33 tailshaft for $120

Walbro is actually a GSS 341. (Basically the same as the 342 anyway)

As the title states im after a dump pipe and front pipe for a GT3582 which is high mounted and externally gated for a rb25det. Im located on the gold coast but will pay for shipping if required

bump

Probably $20 would cover it mate. I don't know how old the loom is but it's in good condition. Plugs arent brittle or cracked

Ive also got a RB20 Clutch slave for $40 really need these gone guys

bump

Got Some parts to sell. selling Coilpacks due to purchasing by mistake. and the other parts I was told were Series 1 but are actually Series 2. I have a set of Super spark Coil packs for Series 2. Near new. $240 Series 2 Coil pack Loom $40 Series 2 Pink Label 3 pin AFM in great condtion $50 Walbro GSS 342 Fuel Pump with wiring and filter Sock. Great condition, only selling as I already bought a Bosch. looking for $75 Parts Located on Gold Coast Happy to post at buyers expense Will get pics up soon

Ad the title states I need an ecu/ computer to tune my series 1 rb25det with. Microtech, mines, nistune, hks etc I dont care just something that works and isn't to expensive. I also need the knock sensor and air regulator part of a r33 body loom ( loom down drivers side to fuse box on engine bay) And I need a r32 clutch line Daniel 0422051559

bumpo, need these sold guys

Bump

from looking at pics online i have found that the Negative is black with a yellow strip. and positive is 2 wires. One is full white. the other I cant tell, can anyone tell me the colour of the sencond positive wire?

Yeh Im pretty sure i have the main negative sorted. its black with a yellow stripe. I mainly need the positive wire colours

Anyone? All u need to do is have a quick look at the stock battery terminals

Can anyone take a look at the wire colours for me?

Just a quick one. The battery terminals have been taken off my wiring loom and I need to relocate my battery to my boot. I need to know the colours of the wires going to the positive terminal and the same for the negative. I think the negative is a black a faint yellow stripe? Also if someone knows the wire colours for the 32 gearbox for the reverse and neutral signal? The plug terminals have been ripped off the gearbox... Any help very much appreciated guys