jomsy

1:18 kyosho gtr's Hi all, I have 1x axia gtr and 1x stp gtr for sale, both 1:18 scale made by kyosho, both really dusty/dirty but other wise great condition, no boxes $200 for both pick up only please from western sydney pm me you number and I can SMS some pic's if your interested

should be 30 each

hi guys ive had these in storage forever and would rather someone use them i dont have exact measurements but they are all around 60cm x 100cm give or take, the dr30 is a bit wilder shoot me some pm if interested. i think around $30 plus postage

Whats the width and offset for stock r33 and r34 gtst rims, i know the pcd is 5x114.3 im sure its been covered before but i cant find it

i got 4 sale 5 dicast GTR's, they are 25cm long, they are the Winfield racing, HKS, STP taisan, calsonic, axia, these are worth $200plus in the model shops, take all 5 for $500 located in Sydney, email me at [email protected]

will fit gts,gtst etc...

I got my Works emotion Cr rims for sale, they are 17x7 with +43 offset 5 hole 114.3, bronze coloured with 215/45/17 Yokohama's Rims and tyres have done about 1000kms, like new, Works stickers havent been stuck on rims yet selling to get some 16" rays rims asking $2100 located in Sydney email me at [email protected] if interested

i got a complete diff (minus the diff center) with 4.7:1 gear set, came out of an s13, but should fit gtst and similar, good ratio for drifting located in sydney looking for offers around $100 email me at [email protected]

Consider a straight swap for a 2000, integra type r

Im selling my type r to make way 4 a new house, its championship white, red recaro seats, 45000kms ,full honda service history, Aftermarket exhaust, Genuine mugen pedels and topfuel carbon intake chamber, has std Rims painted black, plus original white rims asking for 30,000 ono located in sydney email [email protected] or call 0409129422

pic:

ok it has power window, they all work, power steer, and has a spare turbo, distributor, and complete intake manifold, it did have a/c but the pump was no good so i turfed it, momo steering wheel, nismo gearknob , hks boost guage and turbo timer, factory interior thats red n black, and power adjustable drivers seat, im selling it because over a year ago i had a 500hp engine in it that blown up big time, hence no engine, and its just been collectiog dust eversince

nah engine bay not sprayed,too much stuff to remove and refit i got some pics, but i cant seem to upload them, email me if you want to c them

quick rundown on how to do it, remove the following parts 1- fan shroud and engine fan, 2- intake cross over pipe, 3-leave intake manifold on head, just remove fuel hoses, and wiring, and some other hoses you will see then if you forget them when you lift of the head 4- crank angle sensor and covers 5 all the belts, a/c , steer, alt 6- put motor on top dead center 7- remove balancer and lower cover 8- mark camgears and crank gear with liqud paper in (ie put a dot on the gear and on the belt) 9- loosen tensioner and remove belt 10- take of plug cover and rocker covers 11- drop the exhaust at the dump pipe 12- remove turbo feed hoses (the hardest bit of the whole job) 13- you may have to remove the cams to get to the head bolts just check i can remember its not hard 14- remove head bolts 15- get someone to help you lift the head off, check nothing is still attached, ie hoses wiring small bolts 16- idealy get the head checked, get a razor blade and scrap away the old head gasket of head and block then sand it with some wet n dry cleanlyness is the key hear 17- wipe down with a clean rag and re assemble in the reverese order, just torque up the head bolts to correct tension piece of cake really, it honestly isnt that hard to do, so long as your not a complete tool

sorry, id prefere to sell it complete, do have a spare lsd centre because i replaced it with a full spool diff, but the next owner might not like excessive oversteer, s13 silvia diff interenals can be made to fit its what i did

I have a 84 Skyline DR30rs 2 door for sale,Its been resprayed tiga mica gold, Has JIC coilovers,trust F/M intercooler, 6 point bolt in rollcage, strut brace, and fibre glass bonnet, 3" exhaust, it has full engeneers and import paper work and has been registered in NSW, only thing is it doesnt have an engine looking for around $3500 email me at [email protected]