Jump to content
SAU Community

Recommended Posts

Hi

Details on car and drivetrain/powertrain

Car Details

1990 R32 GTR

Gunmetal Grey (fresh respray)

Nismo Rear Boot Lip

Nismo Headlights (N1)

Nismo Bonnet Lip

Nismo Shocks and Springs

Nismo Front Tie Rods

Immaculate Interior

R34 GTR Wheels with new tyres

90,000kms

Engine

RB26 Head

Full Head Service

Mild Port/Polish

HKS Cam Gears

HKS 272 Inlet/Exhaust Cams

RB30 Bottom End

Compression Ratio 9.0:1

CP Forged Pistons and Rings

Carrillo H-Beam Rods

ACL Race Bearings

R33 GTR Oil Pump

R33 GTR Water Pump

Oil Restrictors (limit oil flow to the head)

Balanced Crank and rotating assembly

ARP Head Stud Kit

Custom 4WD Sump Adapter

Modified Sump and pickup

Garrett T04Z Turbo

Custom Exhaust Manifold

SubZero 55mm Waste gate

Sard 700cc Injectors

R33 GTR In-Tank Pump (used as lift pump)

2.5L Surge Tank

Bosch 044 Fuel Pump

Nismo Fuel Regulator

100mm Intercooler and custom piping

Nismo Engine Oil Cooler

4" Exhaust System

ARC Air box

Apexi PowerFC Engine Management (with Datalogit Software)

Apexi Boost Controller

R33 GTR Gearbox with OS Giken 5 Speed Cross Gear Set and rebuilt transfer case

Exedy Twin Plate Clutch and Flywheel

As we speak the engine is being built but i am happy to sell you the car with the fresh engine either installed and tuned or i can sell you the car and the assembled engine separate.

This car will easily make the 450-500kw at all four wheels as stated.

Pricing

Car (without engine or box) $16,000ono

Car (with engine and box not fitted) $28,000ono

Car (with engine/box fitted and tuned) $32,000ono

For more info [email protected] or PM me

Edited by NissanFreak

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello, sorry for being late to join the discussion, but my clock just died on me.   Ive tried to look at Michaels digital clock repair.docx and it doesnt work maybe the file has expired.   Please let me know if you can re upload it or take some youtube videos to show us how to get the clock installed? thanks
    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
×
×
  • Create New...