Jump to content
SAU Community

Recommended Posts

I was thinking, would it be worth the effort of insulating the air conditioning lines, especially the ones that go along near the exhaust area? The main reason I'm thinking about it is I have a whole lot of thermal wrap which I pulled off my rusting dump pipe recently, and it's kind of in bits and pieces and not really useable for much else. I was thinking I might salvage what I can and try wrapping it around some of the aircon lines. Anywhere else I should try wrapping it?

Link to comment
https://www.sau.com.au/forums/topic/111737-insulating-airconditioning-lines/
Share on other sites

My brothers R31 has silver, alfoil type sleeve over the lines that run up past the exhaust manifold.

Don't think it would be standard factory fitment, but it may have been, anyone clarify?

Protecting them from the radiant heat from the exhaust manifold is a worthwhile proposition.

Its not going to effect ac performance a great deal, but it will extend the physical life of the rubber hoses.

I've got that foil stuff in that area too, but I think there are lines which run past there forwards. There's probably not a whole lot of difference insulation can make while the car is moving, but it might make the air a little cooler when idling in summer traffic. I guess I'll just try it and see, I think the only other use for this stuffed heatwrap is to throw it out.

I did it on my last car (Berlina V8). I didn't notice any difference in the A/C efficiency, but I don't see why it can't help? My lines were thin metal pipes that went from the gas cylinder to the A/C compressor and condenser.

Heck... why not!? =-]

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...