Jump to content
SAU Community

Recommended Posts

these seats and rails were originally out of a fresh import gtr32 - the owner was quite big and didn't fit. For my s15 (and all silvias/180s), one mounting point was approx. 3cm too short so that bracket was cut off and a new plate welded on by a professional. To have this fit skylines again all you need to do is drill a hole approx. 3cm in, no welding required.

the seats have no branding - choosen because i didn't want to have a big bride/sparco/recaro logo that say "steal me!"

the harnesses can fit with no modifications; if you want to run with the optional 5th and 6th point (that go around your crotch area) then you will need to find a mounting point below the seat.

:)

Link to comment
https://www.sau.com.au/forums/topic/125583-sold/#findComment-2319745
Share on other sites

Any chance of getting some more photos of the seats (front, side and back) in full detail?

Also, I have a coupe; how is this going to affect people climbing into the back as they're fixed buckets

Link to comment
https://www.sau.com.au/forums/topic/125583-sold/#findComment-2319754
Share on other sites

  • 1 month later...

i will sell the drivers side seperately:

drivers side bucket + rail = $550

1 x 3" harness = $250

together = $750

IIRC the A31 rails are the same as R32/33/34 rails, so if i do remmeber correctly the rails will fit your A31 :(

Edited by _Wing_
Link to comment
https://www.sau.com.au/forums/topic/125583-sold/#findComment-2447004
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pads for R32 GTS-t, R32 GT-R non V-Spec (Sumitomo), R33 GTS-t and R34 GT-t are all interchangeable. R34 GT uses a 2x piston caliper, hence it didn't fit.
    • Checked with amayama and nope, the full S2 manual set is not available anymore. Unsurprising, but still disappointing as the ? on availability gave a glimmer of hope.
    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
×
×
  • Create New...