Jump to content
SAU Community

Recommended Posts

Moving interstate cannot finish this one off!

Come and grab a bargain or trade me an R32 Skyline

1993 Nissan 180sx, SIL80

RB25DET conversion, RB20 box

BN Blister full kit

S14 seats

For more info, see nissansilvia

PM if interested

cheers

sil80side.jpg

sil80front.jpg

sil80engine.jpg

Edited by pssiii
Link to comment
https://www.sau.com.au/forums/topic/137300-sold/
Share on other sites

to answer some of the FAQs, the car has been complied, is registered til Feb 07 and the conversion has been engineered and mod plated.

it's registered as a 6cyl, so snap it up while there's plenty of rego left!

Link to comment
https://www.sau.com.au/forums/topic/137300-sold/#findComment-2572521
Share on other sites

do you have the details of what was done during the conversion?

my mate's looking for a sil80, but most of those he had seen were just bodykit conversions.

This isn't a genuine Sil80, it is a converted 180sx. It was bought already converted, but I believe it's still got the 180sx reo etc.

PM if your mate would like to check it out

Edited by pssiii
Link to comment
https://www.sau.com.au/forums/topic/137300-sold/#findComment-2607682
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...