Jump to content
SAU Community

Help...head unit connection..

sidewaymambo

By sidewaymambo,
in Car Audio & Electrical

 Share

Recommended Posts

sidewaymambo Mentor

sidewaymambo

Posted
Posted

Hi, guys

I try to install a head unit, to replace the factory one. i have search the faq (assume R33 has same loom as R32):

http://www.powerlink.co.nz/~graeme/faq/74.html

Yellow with Silver Tracer ------> Constant 12V

Black with Red Stripe ---------->Electric Aerial

Blue with Silver Tracer---------> Ignition 12V.

Red with Blue Stripe ---------->12V when lights on.

I 'd like to try connect those wires from head unit to the loom, however I have some problem, from the instruction of the head unit, I don't have problem for speakers cables, however I am not sure the rest wires hanging there:

From my head unit, where I should connect these wires to

1) there is a filter box (fuse 7A) has two wires:

yellow----->backup

black------> ground (-)

2) Blue wire with FUSE (0.5A) ----> Auto Ant (+)

3) Red wire with FUSE (1A) ACC. B (+)

I guess that the blue wire goes to black with red stripe (electric aerial)...but how about the rest?

thanks for any information..

Link to comment
https://www.sau.com.au/forums/topic/1399-helphead-unit-connection/
Share on other sites
Guest Boxhead

Guest Boxhead

Posted
Posted

yes i have had sagas when installing my stereo, firstly this canadian mate i have tryed, it worked for a while, then pete smith decided to re wire it etc... and its going great now..

however we did notice last time we were in ricebarn (auto barn)...

that they have these adapters for head units etc..

like nissan to pionneer, or nissan to kenwood etc

im not sure if these could help you, but im led to beleiev you plug the old plugs from stock cd player, into one end of the adapter, then it clicks into teh back of new stereo...

dAVE Grand Master

dAVE

Posted
Posted

it should have come with its own loom. Then all u do is cut out the factory nissan one and wire it into your new loom according to the wiring diag that came with the stereo.

U might find some dont get used on the stereo side - eg power ant etc, and from the other side, u might find that your head unit doesnt have dimming, so u will have extra wires left.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Borg Warner EFR Series Turbo's V 2.0

      By GTSBoy · Posted

      Photo of manifold showing gate location? I mean, it's 6Boost, so we probably shouldn't be worrying, but always wroth knowing what the layout is. Plumbed back to atmosphere? Or into the dump?
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yes correct. Also, I'd avoid applying it to soft paint (however I doubt you'll ever have to deal with it in practice). So any paint that hasn't fully hardened, could be a 1k paint that never fully hardened or it could be a 2k paint that was laid down thick and hasn't yet fully hardened. 
    • kevboost7
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By kevboost7 · Posted

      Wow, i wish i found this sooner.
    • Borci88
      Borg Warner EFR Series Turbo's V 2.0

      By Borci88 · Posted

      Bit of an update to this one. Having some issues on the dyno that held us back (boost spiking) and I want to pass some info over you guys and see what you think is wrong with my setup. The current readout on this dyno is 462rwkw on a low reading dyno so keep in mind it is a real world 500rwkw setup on a hub dyno. Don't read into the power figure too much as a sign of the issue. The short and curly of it is: 2.8 Litre Racepace build RB25 NEO N/A Head with VCT (internally standard however ) Borgwarner EFR 8474  Turbosmart 50mm Straight Gate + Mac valve 6Boost Manifold 4" dump to full 4" exhaust (nil restrictions) Wastegate plumbed back in and all angles in the exhaust system are acceptable and not too sharp. GFB SV52 BOV in cooler piping  Turbosmart BOV in EFR Housing   The issue we are having is it comes onto full boost for example at 4000rpm and spikes to 24/25psi, before dropping down to 17psi before slowly rising back up to the target boost of 23psi. It was extremely uncontrollable and the tuner actually had to ramp in boost progrssively with each 1000rpm on each boost setting we selected to try and reduce the amount of spiking. Sometimes we would see a drop of 10psi from the peak at the beginning of the run, to the low, until it took the next 500-1000rpm to stabilise back up to the target boost. The tuner is pretty confident that the straight gate is just a poorly designed product and leaks too much boost upon cracking the gate open and theres no way to fix it other than going to a poppet valve. He's also confient theres no ignition breakdown or floating valves. The fueling is extremely stable as well. Turbo speed is somewhere around the 109,000rpm area. The spanner in the works for me is that prior to this Borgwarner and StraightGate, the car was tuned on -5 twins at a diferent tuner, and he also had issues controlling the boost with it spiking around the same rpm range, so to me this sounds like the same issue and it can't be anything on the turbo side as this was all changed and I think the behaviour is extremely similar, if not the same. We also removed the mac valve and did a run on wastegate pressure and it still spiked and had the same behaviour. My thoughts on possibilities are: Boost Leak VCT Cam Gear isn't reliably activating consistently - (On this however, we did a run with the VCT disabled and the boost still spiked) Turbosmart BOV is not handling the boost? However this seems unlikely to not be able to handle 20psi. I have a couple of logs that I can't make sense of if anybody knows how to read them and can obtain further logs of other parameters if they are not enough, happy to pay for anyones time. The dyno readout with the power figure is the most recent last week. The other picture is from two weeks prior to that where we couldn't break 400kw (we removed the cat), however the issue of the boost control persisted. @Lithium @Piggaz @burn4005 @GTSBoy @discopotato03 I've tagged those that were quite active in recent pages here, no disrespect to those that know turbos well but I missed tagging. Cheers 
    • Chocolate Cheesecake.
      Infiniti Q60 Navigation Update

      By Chocolate Cheesecake. · Posted

      I recently purchased a 2018 Infiniti Q60, which has an SD card navigation map. I can see my system has options for real time traffic updates etc, and am wondering if there is something I can purchase to get this working? I can see there are at least updated maps for USA and Canada, but nothing for Australia. Surely Infiniti took changing road systems and city expansions into account when they decided to use an inbuilt navigation over Android Auto/Apple Car Play, or are we doomed to drive on streets that don't exist in the navigation system if you drive to a new area?
×
×
  • Create New...