Jump to content
SAU Community

Recommended Posts

hey all have a few parts that i need gone

postage at buyers expense all prices negotiable!!!

located in camden, sydney

anymore info please pm, sms or call on 0422258117

if u want anymore pictures of any of the items listed pm me ur email address and i will send asap

cheers

brad

- Redtop ECCS Rb20det plenum (top half) has been ported/deburred inside and is in good condition no throttle body everything else is there can be used on silvertop $50 ono

- Silvertop Rb20det complete inlet manifold no throttle body/injectors/canister for aac valve is in good condition $50 ono

- Silvertop Rb20det cam covers, sprayed in XR6 orange good condition $40 ono SOLD

- Silvertop Rb20det injectors have been leak tested all ok $70 ono

- Garrett T4/T3 turbo in need of rebuild (seals/bearings), everything else in good condition, has 0.70 A/R front housing with T4 compressor wheel and shaft, has VL turbo rear housing with 0.63 A/R large T4 wheel

comes with dump pipe, want gone $150 ono

dsc00017lt1.th.jpg

dsc00008hs3.th.jpg

dsc00009bi5.th.jpg SOLD

- turbosmart veeport BOV good condition $100 ono

dsc00031vi2.th.jpg

- inlet return pipe to suit the above BOV, replaces the pipe JUST before the elbow pipe to throttle, has adaptor to suit turbosmart BOV black in colour (pipe in pic above) $40 ono

- assorted parts

* front VL berlina apron the part over the headlights in primer good condition genuine holden $30 ono

* VL Rear bumper complete in asteriod silver few small chips but in good condition $30 ono

* 2 VL Air Flow Meters one off rb30 skyline the other off rb30 VL good condition $30 ono each

* single piece manual tailshaft to suit rb20det/MF5 RB30 N/A gearbox good condition $40 ono

* VL Noltec front camber/castor adjustable poly-urethane pillow ball tops blue in colour good condition

bought for $250 want around $80 ono

dsc00033qf5.th.jpg SOLD

* VL N/A manual starter motor good condition can be used on Rb20det if want $30 ono

* intake pipe painted silver for standard T3 turbo with 3'' Simota pod in good condition gives good dose

$30 ono

dsc00032kg1.th.jpg

* JBL 12'' GT4 subwoofer 1000watt near new condition bought for $170 2 years ago want around $50 ono

dsc00030qv6.th.jpg

Edited by RB20/30Det_VL

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Was that with the cas upside or correct way up?
    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
×
×
  • Create New...