Jump to content
SAU Community

Recommended Posts

Hey guys,

I am looking at getting new rims for my car, which I recently imported.

I dont know what to go for 18" or 19"

I am decided on the 8" front and 9.5" at the rear!

I am even decided on the rim! good old Impuls in chome or shadow chome!

what I dont not know is what size to go for.

What profile of tyre would be on each size of rim?

I have a ute at the moment with 20" running 30 profile tyres on hard suspension.

My critera are;

I would like a more enjoyable ride this time round! and to suit performance!

What do I get? please help! with advise. :(

Edited by Tezza
Link to comment
https://www.sau.com.au/forums/topic/141985-shopping-for-rims/
Share on other sites

Cool, in that case, i have a set of 18x9.5's all round, stretched 235's over them, if you're just coasting along and not holding the wheel it will tramline, but as long as you're holding the wheel its ok

Ride isnt that bad, i have TEINs aswel though, so they dont help

Thing is, ive got Kuhmo Ecstas on there and they're shit, decent grip in the wet until you plant it (yes all 4 wheels light up) but they're hard wearing so you get value for money, andway thats a different side of it, its the rims you need

Most people get them from Tempe Tyres in Sydney, they deliver aswel so if you're not in Sydney they can still help you out, personally id never buy anything from them again due to past experiences, but its up to you

Anything else, just ask :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...