Jump to content
SAU Community

Recommended Posts

hi guys im intrested in joining u in the cruise and i hope that i'll be welcome. I havn't met any of u guys yet; well as far as i know. :D could sum1 plz explain to me where r u guys crusing around so is it just around wisemans?

  • Replies 376
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

hi guys im intrested in joining u in the cruise and i hope that i'll be welcome. I havn't met any of u guys yet; well as far as i know. :D could sum1 plz explain to me where r u guys crusing around so is it just around wisemans?

You'd be more than welcome :)

The cruise is generally from the meeting point, to the destination. When we get there, we stop off for lunch, photos, a yarn etc (we chat at the initial meet etc too). After that we make our way back, maybe have a few stops and yea. Do what ever after that.

It'll be from thornleigh, to wisemans, and then old pac back home.

Anyone wanna leave from richmond PM me.. ill probably be at the carwash at shell on windsor st in the morning some time before the cruise

I'll meet you there Slim!

What time? Around 8:00am?

:drool: at the CRAVED mobile!!!! i feel so honoured that he'd grace my cruise with his presence!!! he was at my very first one too! wow! thats two of my cruises!!! *sits there in awe*

ROFL

it was black then though and you didnt talk to me hahaha

hang on... thornleigh, wisemans, thornleigh then back again is what you meant, i think :P

wel it doesnt say which way we are going, so it could be

richmond--> windsor --> thornleigh --> windsor --> wisemans --> old pac --> thornleigh --> windsor --> richmond




  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...