Jump to content
SAU Community

Recommended Posts

im selling a used (barely) kkr430 with the dump pipe and v-band clamp. almost brand new condition with bugger all shaft play. driven less than approximately 2000km's.

i currently dont have any pictures, but can be viewed on otomoto's site. http://www.otomoto.com.au/kkrturbo.htm

for those of you who are lazy, here are the specs;

KKR430_lg.jpg

Compressor inlet pipe 69mm, compressor outlet pipe 50mm

48 trim compressor; inducer 53mm, exducer 76.5mm

Turbine wheel outlet 48mm, outer diameter 64.5mm

im looking for $650ono, now $500. $400 picked up this weekend only! -melbourne

i want this thing gone! going to buy a new setup next week people!

call Miguel on 0432315388 :happy:

some low quality pics attached

post-30568-1171793937.jpg

post-30568-1171793974.jpg

post-30568-1171794123.jpg

post-30568-1171794164.jpg

Link to comment
https://www.sau.com.au/forums/topic/156831-sold/
Share on other sites

it actually wasnt bolted on to my car, but a mate of mine made 205rwkw on dr.drift's dyno with standard afm and injectors, someone else on these forums made 210rwkw

Link to comment
https://www.sau.com.au/forums/topic/156831-sold/#findComment-2924341
Share on other sites

  • 2 weeks later...
will this be a direct bolt on to an r33 with all the lines suiting the KKR

wanting to know this too...

also whats the power rating of it aaannndd when does boost come on?

Oh and the 205kw your mate made, was that on a 32 or 33?

:D

Musky

Link to comment
https://www.sau.com.au/forums/topic/156831-sold/#findComment-2964368
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...