Jump to content
SAU Community

Recommended Posts

Well last nite at 1 i was driving home. There is this road about 1 min from my house which i usually gun it down.

Well some cops were hiding along a side street. They heard me so followed me home. I pulled up in my driveway, noticed a cop car behind me, i was like shit!

Anyway got done for too low and rears bald. I was lucky, they could of screwed me, so its not really bothering me. They seemed to be nice guys, however luckily had no idea and didnt even pop my hood pheww. They also asked if my 3.5 inch exhaust is stock, which i replied, im not sure, but it went through regency like this a few weeks ago.

So my question is, can i adjust my Teins to the correct height, or is that still illegal, as they only said it was too low, nothin about dampness etc.

Anyhelp appreciated

Thanks

Dean

Link to comment
https://www.sau.com.au/forums/topic/17209-defected-in-my-driveway/
Share on other sites

  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

cool, but why the police station? just go to an transport ministry vehicle inspection centre. police and transport are different entities alltogether. I never..ever go to the police station voluntarily

in my yellow, sometimes the cops give me 2 weeks,if they woke up on the wrong side of bed,theyll give me 7 days,,so check how long he gave you,should be allright. Hope you pass with no troubles

at least u dont have to go to regency man.......u bought ur car from motorcity imports it used to belong to one of the guys at autobahn at mile end..........in my old sileighty i had adjustables that were too low and the cop let me off with my blow off cos i daid the blow off was real quiet and the shoks i can change cos they are adjustable.....

There is a web site some where around that states the specs for all the skylines inc. ride heights.

The ride height is measured from the center of the wheel to the guard. I'm sure you all knew that anyway.

So just get your tape measure out and adjust to factory 4wd specs. :D

My car is a direct import, so its not aussie s/h.

The cop gave me 72 hours to drive it, after that it can only b driven if im gettin repairs done to it.

He said i have to take to to a police station to get the drivng period extended. Then when my booked date at regency comes, i have to take it there for an inspection.

What im worried about is all my other mods, exhaust, BOV, strut brace, airflilter, etc

Will regency check these even thou its not on the defect (only too low and rears bald)

Now im beginning to worry.

So wat do i do, go to the cop shop or a transport ministy inspection thing??

When you go over regency they will check everything.

Is the BOV a plumback one, if not you will need to change it.

Exhaust is ok as long as it is not very loud, easy to put a restrictor in it if it is loud. Airfilter im not sure on, you may be ok with it.

Well I had to throw my air on recirc today 3 times due to crappy old cars blowing excessive smoke while a cop car was sitting next to me, they didn't even blink.

----------

This is one reason why i'm keeping my car 'looking' as stock as possible. i.e ride height, engine bay, wheels.

Enrico, they check every thing, or maybe its just me or my car.

Anyway, initially i got defected for:

1. After market BOV, regardless plumback, no noise, whatever fuvk it is, as long as its aftermarket u cant have it. thats what i was told by this cop, his face is always gonna be in my head.

2. Air filter, ONLY stock one, i was told by this same cop.

Next chapter:

Go to regency, they run through every single thing. Or again maybe its just me or my car.

Anyway, good luck bro.

I'm also going to get on to their www site and see if i can track anything down.. If i can then i will print it out and keep it in my car for an emergency.

I still remember when I first bought my VS V8 Commodore.. Did absolutly nothing wrong was babying it home and I was pulled over. I was 19 at the time.

Is this your car? "yes" ok where the stash spot? "wtf?? what stash spot" they then proceded to stick their hand in the back of my glove box and push everything out on to the floor.. I wasn't a smart arse either that is what i couldn't work out.... he made me so pissed and held me up for 30 mins going over the car. Didn't defect me luckly as the only thing wrong with it is that it was a little low as it had bilstein adj. shocks and lowered suspension so that the guards sat roughly 1 1/2 fingers about the 16" VR GTS mags.. raaaaaaaaaa ... ;) I'll make a new post when i get some info...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
×
×
  • Create New...