Jump to content
SAU Community

Recommended Posts

hi,

the other night i pulled into the servo filled up like normal. go to take off and was hard to start. got it going and left the servo... got down the road, when applying acceleration fuel was being restricted and went to stall. eventually it did (around corner from the servo)

towed it home and realized the fuel pump wasnt priming i checked the fuse, was fine but replaced it anyway... so i took the fuel pump out, got the part no.GSS342 (walbro) and bought a direct replacement. put it in today and same result!

i also noticed that my ECU (microtech LT8) which controls my fuel and ignition was on the floor (fell out from under dash, which has happened before and not harmed anything), but i the checked plugs were in, and they were...

might i ad earlier that day (has happened before and on rare occasions) it was hard to start had to pump accelerator so it would pick the fuel up... thinking it could mean fuel pump was on the way out

what could be the problem?

cheers

Edited by 4drftn
Link to comment
https://www.sau.com.au/forums/topic/183005-fuel-pump-not-priming/
Share on other sites

how much power though? you need a multimeter to test how many volts are getting to the plug. i don't if the microtech works the same but other ecu's will send a signal to a relay to switch and give power to the pump, might be worth checking that. maybe relay is shagged and not giving a good connection when it switches.

fixed the problem... my earth wire was getting no power what so ever... directed an earth wire directly to negative battery and works well.

responding to what QWK32 was saying - aparently the walbro fuel pumps need to run at 13.something volts to run at a full 100%. i may need to run a relay to get it at full working compacity but would it make my car run any different?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...