Jump to content
SAU Community

Recommended Posts

Item:

19" Rays Engineering true 2 piece aluminum wheels

Age:

Not sure to be honest but not anything current

Condition:

TYRES: rears are 275/35/19 profile with 40% rubber on them, the fronts are WANLI 235/35/19 with 80% rubber on them.

The center of the 2 piece wheels are polished alloy, with the sides of the spokes painted silver. The outer rim portion of the wheel is a seamless forged bright polished aluminum.

- One wheels are a small pin hole on the rim which causes air to escape. This can be fixed with a aluminium sealer or by welding. This rim has also been repaired before so is the only one with slight marks on the dish (see pic below).

- Been told the 2 fronts need some work as at speeds of 70kmph+ there is vibration. They maybe able to just need a re-roll or 2 new dishes might be the way to go. whatever is cheaper.

- one rear has slight gutter rub marks. Only noticable at close inspection.

Price:

$1500.00ono with tyres. Will sell minus rubber at negotiated price. NEED QUICK SALE!!!!!

To Fit: (What car)

5\114 Stud pattern vehicles. (skyline, ford, toyota, etc)

Location:

S.E. Melbourne

Contact:

Via PM

Comments:

- The front wheels (19" dia.) are 8.5"

- The back wheels (19" dia.) are 9.5"

Reason for sale is because I have a 4door skyline and the rears will need rolling and flaring to fit also small spacers are required because im running coilovers and they hit the springs.

These are not cheap rims to buy and hard to get our hands on. They only needs 2 new dishes\fixing the fronts would make it a cheap package overall for lightweight 2 piece rims.

post-24576-1192575046_thumb.jpg

post-24576-1192575052_thumb.jpg

post-24576-1192575059_thumb.jpg

Edited by DEJA VU
Link to comment
https://www.sau.com.au/forums/topic/189580-sold/
Share on other sites

BUMP!!!

also open to swaps\trade for any of these:

- pair of Semi or full slicks (new or used)

- Coilovers for R34 or S13

- Stereo gear

- Stock R34 GTT wheels

Edited by DEJA VU
Link to comment
https://www.sau.com.au/forums/topic/189580-sold/#findComment-3427933
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • About $4k brand new, available from vendors in Oz, or via an importer from Japan. Although that is for an R34 box, so you also need to buy the push clutch front plate (brand new from Nissan) and swap that over, and drill the bellhousing for a push clutch slave cylinder.
    • Absolutely could be. I collected data logs from when the O2 sensor was still out and also after I had replaced it so will try to compare them. Pretty confident that the affect is lowered with the new sensor, will check logs at the same RPMs/conditions. 
    • Hey guys Long time lurker, I daily a nm35 stagea 250t rs four and I've had it for almost 2 years (very reliable 👌). Issues or just looking for information ill always find myself here having a read, so thought id join.  3inch stainless intake, pod filter, AM performance turbo dump pipe, 3inch hotdog, 3 and half inch stainless to 3 and half inch AM performance blast pipes. Bc racing coilovers. 18inch rims Hdi intercooler and trans cooler soon.  Here's my car
    • thanks for the advice on the box... i was thinking the 6 speed was better for cruising on the highway but on closer inspection and comparison the Rb 5 speed box was not too different...  So the choice is going to be the RB25 box... if I can save up and find one at the right price  
    • Thanks Matt, yes that's what i am aiming for. Just going to apply the right voltage and grounds to the dash connector. Hence my search for these pins... any chance you know if these pins are in the same spot as the ones on the S15 Dash connector? as mentioned above on page 8?
×
×
  • Create New...