Jump to content
SAU Community

Microtech Ltx 12

jas/slo32
 Share

Recommended Posts

jas/slo32 Proficient

jas/slo32

Posted
Posted (edited)

Item:microtech ltx 12 with hand controller Condition:still running on my race car

Price:$850 plus freight

To Fit:will suit all rb engines with a couple of wire changes

Location:theodore 4719

Contact:jason 0424348521

Comments:currently on a rb26 buy the plug n play adaptor to suit rb20 or rb25

will freight australia wide at buyers cost

Edited by jas/slo32
Link to comment
https://www.sau.com.au/forums/topic/194414-microtech-ltx-12/
Share on other sites
jas/slo32 Proficient

jas/slo32

Posted
  • Author
Posted (edited)

price drop selling without loom as loom was wired in at the kick panel will still supply loom but its only 6 inches long. plug n play adaptors available from microtech no wiring required also cheaper than paying someone to wire it

Edited by jas/slo32
unarmed_skyline Experienced

unarmed_skyline

Posted
Posted

when i bought my adaptor loom it was $500, which is around about the price to have them wired in but you get the capibilities of being able to remove and not have to chop up your wiring loom,

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      Looking for someone with a R34 front bar

      By GTSBoy · Posted

      That looks good, but I think you're going to need much beefier side skirts now.
    • GTSBoy
      Most women will agree that parking is the most taxing part of driving

      By GTSBoy · Posted

      They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • GTSBoy
      new 1.5 LSD issues/concerns

      By GTSBoy · Posted

      I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • GTSBoy
      M35 Brake caliper replacement

      By GTSBoy · Posted

      Define "starting to fail". Wy not just rebuild them?
    • GTSBoy
      S1 rb25/s14 starting problem

      By GTSBoy · Posted

      Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...