Jump to content
SAU Community

Recommended Posts

Best $10 i have ever spent.

For anyone that has a Steam account (or those looking for an excuse to get one), go and buy Audiosurf. If you don't know what it is, its basically a game that creates a race track that is determined by the speed, beat and intensity of the song you choose to play. Hard to explain so watch these videos:

There are around 15 different game modes including avoid the greys, collect the colours, 2 player and colour match up. The best part is it can be ANY mp3, wma, itunes etc audio format that you have locally on your computer.

Its addictive though so be prepared to waste a lot of time on it :laugh:

Link to comment
https://www.sau.com.au/forums/topic/207514-audiosurf/
Share on other sites

This www.zgeek.com review sums it up perfectly.

Audiosurf is what you would get if Dance Dance Revolution had a bastard child with Fzero, and they raised it in a Tron universe.

You control a speeding car on a track, which is generated by the mp3 that you select. A slow paced song will get you a track with easy bends and gentle conditions. Load in some heavy metal and hang on as sharp turns bend and veer to the time of the music.

While negotiating the track you pass through colored blocks that collect on your grid. Once three of more same colored blocks join up, they disappear and you get points. (Think Bejeweled meets tetris.)

The whole game jumps, vibrates and pulses with the music that is loaded into it. It is a fluid, enjoyable experience that had me saying "wow!" out loud on many occasions.

You get to choose which sort of car to race in, each one modifying your point collecting strategy. I initially liked using "Pusher", which allows you to guide where your colored blocks go into the grid. However I am starting to become a big fan of "Eraser", which can remove undesirable colors from the grid. (Warm colors like red earn you more points, where as cool colors like blue are low point earners.)

At the end of each race your score is uploaded, and you can see how you did against the rest of the world with each song. I managed to earn a couple of mid and top placings with some of my song selections, however no doubt within a few days once the game spreads in popularity they will fall away to oblivion.

The game comes with a selection of preloaded mp3's to choose from (including the entire Orange Box album), however the best fun is loading up your favorite songs and seeing how they *race*.

There *is* local Co-op available, however I have not had the ability to try it so it remains unscored.

The cost is $9.95 American, and is downloadable on Steam. I think this is great value. If you are a music fan, a racing fan, a puzzle fan, or anywhere in between, its pretty hard to go wrong. There is a demo available, so you have nothing to lose.

Link to comment
https://www.sau.com.au/forums/topic/207514-audiosurf/#findComment-3670485
Share on other sites

  • 1 month later...
  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...