Jump to content
SAU Community

Recommended Posts

Nearly complete solution for a large turbo setup, just add the turbo. Comes with Xforce high-rise manifold and a custom 4" front pipe which plumbs up nicely to the normal mounting position. The wastegate is plumbed back into the front pipe. Wastegate is a Turbosmart Progate 48MM. The manifold and wastegate have done around 2000klm's and are in EC. It comes with the two Vbands clamps and 7+14 psi springs.

Manifold cost me $600 Progate cost $850 4" Exhaust $400 = $1850

Selling for $900

No offers thanks.

First with a deposit gets it.

Cheers

[email protected]

post-1044-1215521449_thumb.jpg

post-1044-1215521474_thumb.jpg

Nearly complete solution for a large turbo setup, just add the turbo. Comes with Xforce high-rise manifold and a custom 4" front pipe which plumbs up nicely to the normal mounting position. The wastegate is plumbed back into the front pipe. Wastegate is a Turbosmart Progate 48MM. The manifold and wastegate have done around 2000klm's and are in EC. It comes with the two Vbands clamps and 7+14 psi springs.

Manifold cost me $600 Progate cost $850 4" Exhaust $400 = $1850

Selling for $900

No offers thanks.

First with a deposit gets it.

Cheers

[email protected]

$800 cash on pickup?

Not much while its been in the shed. When it was in the car I had yet to wind it up as I kept lunching clutches. The 25/30 has forged internals and runs a 8.5:1 comp so I can happily blow 20psi down its neck when I have finished Pharking around with it. :)

Sorry about the delay in pic's. Definitely going up tonight guys. BlackR33, I have a multiple buyers that are close so it's still $900 and the first in with a deppie gets it!

All PM's replied.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...