Jump to content
SAU Community

Recommended Posts

there is a high and low setting in the power steering

now low is for under 80km/hr and high is for over 80km/hr

the high setting is where 4ws kicks in. the steering is also heavier than on the low setting

when the steering wheel moves more than 20 deg. (correct me on this one guys) either way the rear wheels flick in the opposite direction 1 deg until the steering wheel is returned to lower than the 20 deg set by nissan

if im wrong here will anyone correct me on it

Link to comment
https://www.sau.com.au/forums/topic/22804-hicas-4ws/#findComment-489330
Share on other sites

HICAS is Nissan’s version of four wheel steering. It is an acronym for High Capacity Actively Controlled Suspension. Unlike other Japanese car manufacturers 4WS (eg Honda’s system) HICAS never exceeds +/- 1°. It is designed for high speed response rather than parking manoeuvres.

The system is electro-hydraulic - the ECU in the boot directs a hydraulic actuator at the rear axle to steer the rear wheels using the rearmost suspension links. The result is usually no more than 0.4° of movement. HICAS gives a touch of counter steer before settling with the rear wheel pointing the same way as the front. (Maybe this explains why my Skyline feels so loose on high-speed gravel...) This results in sharp turn-in, and enhanced stability at medium to high speeds.

off this website.....

http://www.overflow.250x.com/diagnostics.htm

Cheers

Lawrence

Link to comment
https://www.sau.com.au/forums/topic/22804-hicas-4ws/#findComment-490021
Share on other sites

how do i know if i have it guys?

i can see the outline of what seems to be a hicas light on e dash but it never have even lit up before.

my mechanic told me that some cars have hicas and it doesnt light up when starting or ever unless theres a failure or sumfin sumfin

any easy identifiable way to find out?

Link to comment
https://www.sau.com.au/forums/topic/22804-hicas-4ws/#findComment-492890
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...