Jump to content
SAU Community

Recommended Posts

Emanage Ultimate (was only used for about 3 months)

+ universal harness

+ map sensor & map sensor harness (brand new)

+ AFR input harness

cost me $1050 sell for $700

also have innovative LM-1 wideband + RPM converter (was only used for about 3 months)

cost $500 sell $400

or buy both for $1000, everything you need to tune your car yourself

Brisbane

some pictures, why can't I edit my first post??

also have a mdf parcel shelf for 6x9's fits in the back really well

$30

also have gizzmo boost controller, I accidently broke the wires off on the solenoid coil, but I found a place that will sell me a new one for $35 + gst

so will sell for $200 and you get new solenoid or $250 and ill get the solenoid.

post-36364-1216337766_thumb.jpg

post-36364-1216337993_thumb.jpg

post-36364-1216338163_thumb.jpg

post-36364-1216338396_thumb.jpg

Edited by SevenAngryPenguins

I have a Power FC as well $1200, I've had this for less than 12 months and actually used it for only about 4 months, hand controller is in as new condition.

As a note I had this in my car but it stopped working after I installed new injectors, so it was sent to Japan for repair under warranty however it was tested by apexi and they found it working 100% and said problem was with the car.

post-36364-1216625534_thumb.jpg

but yeah if it doesn't work ill definitely refund.

this no editing posts sucks balls.

also since i didn't add its for ecr33

Edited by SevenAngryPenguins

how did the e-manage go on your car?

like did it run well and stuff

and did you need the map sensor & map sensor harness and

AFR input harness to install and run it ?

I had highflow turbo and s15 injectors and it ran really well never had it dynoed but was probably making about 300hp atw, it took a lot of time playing around with the laptop to get it right though since I tuned it myself on the road. I wasn't using the map sensor at the time but was just about to (before I got t-boned) stock afm maxes out really early so it gives you crappy resolution for tuning. For the price its a sweet computer but a lot of stuffing around with the initial setup compared to say a pfc which is virtually plug and play

Edited by SevenAngryPenguins
  • 2 weeks later...
  • 2 weeks later...
  • 4 weeks later...


  • Similar Content

  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...