Jump to content
SAU Community

Recommended Posts

Item:

GReddy Profec B-Spec II Electronic Boost Controller (Black)

Age:

Brand New. Opened the box about 3 months ago to see what was inside but that's it. Never ended up getting it installed so its just been sitting here.

Condition:

Mint condition. Never used before.

Price:

$375 + Postage (Pickup Available)

To Fit: (What car)

Any far as I know.

Location:

Hampton Park - SE Suburbs in Melbourne

Contact:

SMS 0401015236 or PM Me.

Comments:

Bought this around 3-4 months ago from eBay to install into my car but since I'm on my P's I decided maybe its best to not go crazy with trying to get too much power out of my car til im off my P's so instead of just leaving it here sitting here in the box id rather just get rid of it.

Item Description:

The PRofec B-spec II is a new electronic boost controller which offers most necessary functions in its compact body.

  • Blue lighted digital screen shows real-time boost pressure. The digital boost meter comes with peak-hold function.
  • Compact boost control solenoid has capacity to control 300 kpa of boost.
  • Boost preset function allows you to set two different boost settings (HI / LO) and choose one of the settings by using a switch. Also the set boost can be turned off if needed to run the engine at the lowest (original) boost.
  • GReddy PRofec B-spec II allows you to set your desired maximum boost, Gain value, Start boost value, Warning value and Limiter value. These values can be set independently on HI and LO mode

post-42730-1225602993.jpg

post-42730-1225603002_thumb.jpg

post-42730-1225603009_thumb.jpg

post-42730-1225603017_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...