Jump to content
SAU Community

Recommended Posts

Hey guys i got alot of parts im selling, i havent put up some things yet this will be getting updated every week.

CTS coilovers, 8000kms old . fully adjustable, 8 and 6kg springs, can be height adjustaed from the top of the coilover or bottem, damper control, camber tops. etc.

these are awsome coilovers. suit s13/180sx

$1200

Z32 AFM with plug 5000kms old

$250

Custom hard intake pipe painted black, s13/180sx

$150

Apexi pod (super induction kit) with bracket etc to suit z32

$80

Apexi power fc to suit sr20det redtop s13/180sx basicly brand new with handset

$900

Nismo 740cc injectors 5000kms old

$450

Splitfire coilpacks s13/14 5000kms old

450

Cusco front struct brace, suit s13/180sx

$150

Ebay rear stuct brace s13/180sx

$60

CTS Engine damper not cheap s***

$100

Oddesy PC925 batery, 5000kms old aswell

$250

PC 925 Specs:

* 925 cranking amps for 5 seconds

* 870 cranking amps for 10 seconds

* 765 cranking amps for 20 seconds

* Short circuit current over 2400A

* 28 amp hours

* 50 minute reserve capacity with 25amp load

* Female brass terminal w/M6 SS bolt

* Length 6 15/32"

* Width 6 7/8"

* Height 4 7/8"

* Weighs 24 lbs

* Rugged Drycell sealed design

* Military grade

* Vibration resistant

* 60% more starting power

* Deep discharge reserve power

* 2 year storage life

CUSCO front and rear sway bars, awsome condition, s13/180sx

$250 each

180sxparts002ek2.th.jpg

180sxparts003nw3.th.jpg

180sxparts004fd1.th.jpg

180sxparts005xt2.th.jpg

180sxparts006az3.th.jpg

180sxparts007dc6.th.jpg

180sxparts008ts7.th.jpg

180sxparts009xc4.th.jpg

located in qld, willing to ship at buyers expense.

pm for more info.

BLITZ DSBC- duel soliniod so u can run 4 different boost settings, has a little LCD screen so u can see everything your doing. awsome controller it held 20pounds no problems.

$380

Blitz radiator caps x2

$30 each

Greddy oil cap

$50

Greddy gearknob

$50

Greddy sandwich plate for s13/180sx suits s14/15 aswell i think

$170

DEFI guages, only 3 months old. no marks on them comes with EVERYTHING even the water temp holder.

OIL press

oill temp

water temp

boost

control unit 2

$1000

OS gekin twinplate clutch, been rebuilt by jim berry less than 1000kms ago who done the FULL MONTY (best of all best rebuild), cost me $1400 to rebuild. anyone who knows jim berry clutches are awsome, this clutch is very easy to use for a twinplate. cost $2200 brand new, suit sr20det 180sx/s13/14

$1200

Rebuilt s13/180sx sr20det gearbox, brought this to put in my 180sx never got around to it.

$750

MORE PARTS

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Initially I thought having a pair of Recaro seats would be a big bonus, it turns out these do get a little uncomfortable on long journeys (my fault, not the seat). I had a look through the GSM Performance website at reclining seats and booked an appointment to visit their show room. I got the Recaro Sportster CS for the R34 from here, was very happy with the service received so of course a re-visit was in order. Unfortunately the two Corbeau seats I had chosen aren't on display but they had 4 other options available. Two seats dug into my back, one dug into my legs and the other was perfect. I also found out that Recaro seats use a larger bolt pattern so some adaption was required. Luckily GSM offer some universal adaptors that should solve this problem. I searched the interwebs for price comparisons and Corbeau themselves were the cheapest at £300 cheaper (for the pair). I asked GSM if they could price match, unfortunately they couldn't. I later received an email saying Corbeau would honour them the same discount, but the purchase was already made. I did however order the brackets from GSM, both arrived on the same day. I started with the passenger side seat, knowing this was going to be a little trial and error. There are 3 mounting holes at the front and 2 at the rear on these JURAN Racing seat rails.  With the adaptor brackets mounted, the allen cap bolts started to push into the seat, NOT GOOD!  The rear mounting holes lined up but there were issues at the front. The holes were 1/2 hole out, so the brackets got a tickle with the drill to modify the holes. The supplied bolts weren't going to be long enough and a spacer was needed to stop the adaptor bars from bending. A local fasteners company supplied be with some nylon spacers and longer bolts (M8x30, although these will be replaced with 35mm long shortly) A before and after I pre-drilled the front bracket before making a start on the driver's seat to save some time. And in no time at all that was in the car too. The all black seats have transformed the interior and these are MUCH more comfortable. The only downside with the new Corbeau seats is I sit a little higher, but I'll happily accept that over discomfort. The Youtube video can be found here: https://www.youtube.com/watch?v=wPyttKPktXA
    • All 3 I guess. The car came with the JASI Aero 4 door Type R Full Kit unpainted so this was one thing at the top of my list to complete then I noticed there were body panels parts for this kit so i picked them up along with some black mesh to fill in the front bumper and front side air vents. car is at a paint and body shop atm completing this work. Next I will be addressing the internal bells and whistles, great summer project I can do with the kids.  full interior removal - ,boys car sound deadening - pads and spray ,boys stereo, sound, lighting - Big 3, GTT or bigger alternator ,kids head lining - dye black add star lighting mod ,daughter. That's it for the next 5-6 months. I have some motor maintenance  work i have to plan out. oil filter relocation, gaskets, mounts. beyond that, mind is starting to turn over if i can use a DET intake plenum, block off turbo ports & pipe in a air intake.      
    • roller coaster of a ride. Alarm system was removed & main harness was repaired where possible. still no fix just random successful starts. moved on to the replacing the ignition switch and relay. well all this troubleshooting & repair has been going on, the car is at a paint and body shop being pushed around. Ive been going down there on odd days after work to get it sorted.     
    • 5th November if you want to come out for a spin wakfield
    • PROBLEM WAS BROKEN COOLANT SENSOR!!! Replaced with a new one and its running mint.
×
×
  • Create New...