Jump to content
SAU Community

Recommended Posts

this may be a very silly question but i am going to ask away any ways.... when is it time to get a engine rebuild or a new motor all together like how many kms? down the road my R34 is pushing 264,000 kms Dam that Melbourne trip and back to Perth from Geraldton was fun........ haha :D

I just put in New Spark Plugs and coil pack and my nasty Busted WRX Sounding motor is sounding way better now and not a WARNING light to be seen :):P:cool::D:geek:

So the question is how many kms before a new motor is needed?

Edited by DiNoBoNeS
Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/
Share on other sites

until it dies

depends how its been looked after

better = longer

no real number, lots of taxis run around with 600,000kms+

but they leave there cars on all the time and service very often

Tops thanks mate i try and look after her and do the right things i work as a photographer and i leave it running when i am shooting I am only with the guy/gal for like 4 minutes so no need to turn it off and on all the dam time... just was thinking if there was a kms number to do it or if it was the case of wait to it go hehe she is running strong and i do not think it will be for a while i can not wait for 300,000kms.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400195
Share on other sites

when it gets low compression, or has a fair bit of leakage.

leaving a car idling is not ideal either, the fuel isn't burnt correctly, and runs down the side of the bore, washing off the oil with it, and contaminating the oil.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400198
Share on other sites

your car will get hot if its just sitting there idling

best to just let it run for a minute or 2 then turn it off

rebuild it when it pops...

your car gets hot just idleing?

i dare say keeping it running > on and off all the time

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400429
Share on other sites

your car gets hot just idleing?

i dare say keeping it running > on and off all the time

yeh, if you had a digital temp gauge (i use my pfc hand controller) you would see

if your not driving and having air blowing through your cooler etc your car actually heats up at idle

not much but for example

my car usually operates at around 80-82 degrees

i sat in the car park and ate maccas with the air con on one hot day and the temp got up to 105 degrees and went back down after i started driving again

the day and air con did play a part so the temp rise isnt usually as big

best to turn it off..

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400446
Share on other sites

yep.. the only time we realised we hadn't plugged my mates thermo fans back in, was when we pulled into the macca's drive though, and it started to get hot.

most fans will stop, or slow down when the car is moving.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400449
Share on other sites

yeh, if you had a digital temp gauge (i use my pfc hand controller) you would see

if your not driving and having air blowing through your cooler etc your car actually heats up at idle

not much but for example

my car usually operates at around 80-82 degrees

i sat in the car park and ate maccas with the air con on one hot day and the temp got up to 105 degrees and went back down after i started driving again

the day and air con did play a part so the temp rise isnt usually as big

best to turn it off..

That's pretty hot dude.. highest I've ever seen on my 30 is 104deg and that was after a couple of big smokey burnouts on a 40deg day!

FYI boiling point is around 110-115deg.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400565
Share on other sites

yeh, if you had a digital temp gauge (i use my pfc hand controller) you would see

if your not driving and having air blowing through your cooler etc your car actually heats up at idle

not much but for example

my car usually operates at around 80-82 degrees

i sat in the car park and ate maccas with the air con on one hot day and the temp got up to 105 degrees and went back down after i started driving again

the day and air con did play a part so the temp rise isnt usually as big

best to turn it off..

If your car is getting hotter when its idling then something is stuffed. When temps start to rise a bit the fan is suppose to kick in to pull air through and keep temps steady.

My temps don't rise one bit no matter if I'm moving or not. Sits on 73 deg all the time (PFC hand controller and new watter temp sensor). Car also runs an N1 watter pump which doesn't flow as much watter at idle as a normal watter pump and still no issues at all

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400819
Share on other sites

95% of engine wear happens when the engine is cold. Thats why taxis engines start to go at 1,000,000kms, and trucks get their engines rebuilt when they clock back to 0 only because they can. I've worked on trucks with over 500,000kms with engines that are fine, and cars that have bearing noise at just over 200,00kms.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4401253
Share on other sites

If your car is getting hotter when its idling then something is stuffed. When temps start to rise a bit the fan is suppose to kick in to pull air through and keep temps steady.

thats only if you have thermo fans on your car

belt driven fans are constantly working and engine temp SHOULD co up slightly if not moving due to less air movement through the core

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4402123
Share on other sites

(feel free to correct me people)

Oil is a major factor in engine wear.

your engine would run dry for 2 seconds before the cold oil is pumped up to the valves and while the oil is cold its not flowing easily.

I've seen inventions for pre-heating oil sumps before starting, and i'm sure someone will have invented a oil primer.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4403775
Share on other sites

actually the fans on RB's are clutched, they apparently stop moving at higher speeds.

but yes, they are constantly spinning at idle

They don't stop spinning at high rpm, the clutch is there so that the fan isn't spinning at full engine speed at high rpm.

As for oiling, there are products out there that retain oil pressure in a container so that the instant you flick the key, it squirts the pressurised oil through the system immediately prior to startup.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4404321
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Has equal chance of cleaning an AFM and f**king an AFM. I think you can work out what happened. When the Hitachi ECU sees the AFM die and goes into the associated limp mode, then it will start and run just fine, because it ignores the AFM and just runs on idle maps that will do what it needs to get it going. But there is no proper load signal, so that's about all it can do. My suggestion? If you don't want to go full aftermaket ECU, then get some R35 GTR AFM cards and some housings to put them in, in the stock location, and Nistune the ECU. Better to do a good upgrade than just replace shitty 40 year old tech with the same 40 year old tech.
    • So my car was recently having trouble starting on initial crank, I would need to feather the gas for it to start up but besides that it would start and run fine. So I clicked the idle air control valve (with throttle body cleaner) and cleaned the MAF sensors (with MAF cleaner). The start up issue was fixed and now the car turns over without the assist of the throttle, but the car is in limp mode and wont rev past 2.5k RPM. From what I understand the IACV would not put the car in limp mode, so I am to believe it is the MAF sensors, but it was running fine before and now I cant get it out of limp mode. I cleaned the MAF made sure the o rings were seated properly. Made sure the cables were plugged in properly, the cables also both read the same voltage. Does anybody know why this is or what could be causing this or how to get it out of limp mode?
    • Ooo I might actually come and bring the kids, however will leave the shit box home and take the daily
    • Thanks. Yeah I realised that there's no way I'd be able to cover the holes with the filler, it would just fall through. Thanks again @GTSBoy!
    • That was the reason I asked. If you were going to be fully bodge spec, then that type of filler is the extreme bodge way to fill a large gap. But seeing as you're going to use glass sheet, I would only use that fibre reinforced filler if there are places that need a "bit more" after you've finished laying in the sheet. Which, ideally, you wouldn't. You might use a blob of it underneath the sheet, if you need to provide some support from under to keep the level of your sheet repair up as high as it needs to be, to minimise the amount of filler you need on top. Even though you're going bodge spec here, using glass instead of metal, the same rules apply wrt not having half inch deep filler on the top of the repair. Thick filler always ends up shitting the bed earlier than thin filler.
×
×
  • Create New...