Jump to content
SAU Community

E.o.i P-platers Dreammmm 32 Na

bac-draft
 Share

Recommended Posts

bac-draft Explorer

bac-draft

Posted
Posted

hey guys i got a 32 skyline its black with a glitter through it pretty gay but looks ok... was painted about 3 years ago..

it is sittin on 18 inche white wheels with new tread al round..

been lowered with coil overs in rear and not to sure about front...

lookin more for a swap to see what i can get for this thing or just throw us an offer it had 10 months rego aswell with 165.00kms always serviced with brand new clutch drive perfect...

pretty standard interior just got head deck 6's in door and 6by 9's in rear runnin off amp and a 12inch sub in boot..

goes well for non turbo and perfect for p platers..

just pm on here or call me my number is 0435035067

thanks

p.s lookin more for swaps but throw me some offers

post-37430-1234259045_thumb.jpg

post-37430-1234259124_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/256471-eoi-p-platers-dreammmm-32-na/
Share on other sites
Pepsinator Experienced

Pepsinator

Posted
Posted

i have 96 vs commo stock auto, subs head unit, pod filter 18X,XXX

would make a cash adjustment your way

new rego

adelaide

just throwing it out there not expecting much

trying to find a na 32

where bouts in nsw you at?

  • 3 weeks later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • PranK
      2001 R34DE

      By PranK · Posted

      R34DE as in R34 with an RB25DE? So did you get this? Or you planning to?  I'm not really sure what you're saying. 
    • Dose Pipe Sutututu
      What should I do next to hold the head on

      By Dose Pipe Sutututu · Posted

      Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Dose Pipe Sutututu
      boost source Size Garrett gt28 gen2

      By Dose Pipe Sutututu · Posted

      Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
×
×
  • Create New...