Jump to content
SAU Community

Anyone Bought This Short Shifter?

MoogLe
 Share

Recommended Posts

and3_3 Proficient

and3_3

Posted
Posted

Same one i have and as far as i know its the same as the C's one, mine is awesome and there is a tutorial on how to fit them in the tutorial section.

You may need to re-use the bush on the end of it as the one i got was really shit and didnt fit properly, just find the part number and call up a nissan dealer for it. The part number is in a thread somewhere

bubba Grand Master

bubba

Posted
Posted

It *looks* the same as a C's, but personally I would only get a genuine C's shifter.

Is it going on an R32 or R33? a 33 one will fit on a 32 with some knowhow but from what I had to do to get the 33 one to fit the RB20 box I doubt a 32 one would fit a 33.

Swiper the Fox Grand Master

Swiper the Fox

Posted
Posted
It *looks* the same as a C's, but personally I would only get a genuine C's shifter.

Is it going on an R32 or R33? a 33 one will fit on a 32 with some knowhow but from what I had to do to get the 33 one to fit the RB20 box I doubt a 32 one would fit a 33.

I have a genuine C's fitted to my drag car...when teamed with the PPG dogbox its the ultimate in shifting.

Projectile Collaborator

Projectile

Posted
Posted

Hey dude just pull out your current shifter and cut about an inch off it, re-weld it and she's all sweet haha :wave: think that's what my car had done to it, you can't tell the difference, mind was laved though...i'll get a pic if you want. pm me if you want it and i'll post it up here.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Well, this is probably where a wiring diagram and a multimeter come into play.
    • Jarsky
      gauge needle removal

      By Jarsky · Posted

      I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Jarsky
      R33 GTST Axles

      By Jarsky · Posted

      Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Jarsky
      R34 Speedo not working after manual swap

      By Jarsky · Posted

      Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...