Jump to content
SAU Community

Westies Mini Meet And Greet Every First Thursdays Of Each Month

pbk1776

By pbk1776,
in Events Archive

 Share

Recommended Posts

pbk1776 Mentor

pbk1776

Posted
Posted

Hey Guys - this is for all the WESTIES car enthusiast (all welcome even you're not from west lol)

We will have a mini meet and greet every thursday night starting 5th of March. We will do this every first thursday of each month. We will officially start it next month on the 5th. We have started it with all Little Pinkyz group last 12th of Feb.

WE WILL ALL HAVE DINNER!!!!!! and CHAT!!!!!!!!! and a bit of CRUISING!!!!!!!!!

So guys every1 is invited

I will be using this template for where to meet and destination

Where to meet: JUST Check the thread (we will update this every month we will always change the place)

What time: 9.30 to 10.00 pm Time will never change

Destination: (Will Post before the meeting day)

What to bring: YOU AND YOUR RIDE LOL and MONEY and a hungry tummy LOL :) !!!!

pbk1776 Mentor

pbk1776

Posted
  • Author
Posted

Alright People

First official mini meet and greet date

Where to meet: KKs Liverpool middle parking

Time: 9.30 to 10.00 pm

Destination: Mini cruise to and dinner to Rashays Restaurant at Livo or Kebab shop at Carens hill or Ctown KKs lol(next to the bowling lane)

See you there :)

pbk1776 Mentor

pbk1776

Posted
  • Author
Posted
haahha you finally did it!!

cya every month then :blush: except if i have exams o.o

Yeh lol..... Well see you every first thursday man :D unless you guys still wanna meet up in between lol

pbk1776 Mentor

pbk1776

Posted
  • Author
Posted

Keep this post alive guys lol

The last time we held a mini meet for all westies only 4 cars came From SAU :laugh:

Shane

Mitch

Shehan

and ME :)

even the first SAU mini meet only 2 came :laugh:

Me:)

and Shehan

Anyway hope to see more people on the 5th

Looks like all active members or members are from up norht :thumbsup:

pbk1776 Mentor

pbk1776

Posted
  • Author
Posted

Alright People we changed the place and destination

and Also it will be every month not every thursdays anymore :( just too less people turning up we might do it every saturday night

First official mini meet and greet date

Where to meet: North Parra Maccas

Time: 9.30 to 10.00 pm

Destination: Nandos Parra

-FIGJAM- Grand Master

-FIGJAM-

Posted
Posted

hey guys, ill be out of these meets. training finishes close to 9 and i am to tired to go drivin round. also a bit late, i have work in the morning.

I will try and get to them now and then

 Share
Go to topic listing


  • Latest Posts

    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • MBS206
      Chris' Toyota Mark ii JZX110

      By MBS206 · Posted

      I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...