Jump to content
SAU Community

Recommended Posts

the brand is catco

made in usa

HIGH FLOW 3 inch cat converter.

!!!!!WITH FLANGES!!!!!! BOLT ONTO SIL/180/GTST/GTR

also have the hole for the sensor!!!

BARGIN $250 BRAND NEW

U CAN EVEN DO IT YOUR SELF insted of taking to exhaust shop!!!!

Link to comment
https://www.sau.com.au/forums/topic/26284-fs-brand-new-high-flow-cat-3-inch/
Share on other sites

ah ok, yes thats one of the cats i sell.

if you got a bolt on cat, then it wouldnt fit all the cars you stated above, the bolt on cats vary on the type of car as they are not all the same length and the flanges arent on the same angle.

for example r32/33 bolt on is differnet to 180sx bolt on. also 200sx s14-15 have their own different lengths, so it depends on the cat that you have, and what its made to bolt on to.

im assuming its for r32/33, since the 8007 cats are usually made bolt on for these cars.

Originally posted by SKYL9

hey dont wanna burst your bubble but BATMBL sells them for nearly half that price

just thought id have a winge and say that BATMBL does sell 3 inch cats for nearly half my price BUT HOWEVER it is NOT the SAME CAT as im selling. THE one thats nearly half the price is infact a LOWER FLOWING 3 inch cat!

BATMBL also DO sell the one im selling BUT AT VERY VERY SIMILAR PRICE!!!!!!!

sOOOOOOOO............my bubble is still intact

anyways the cat is sold, thanks for letting me have a winge.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
×
×
  • Create New...