Jump to content
SAU Community

Recommended Posts

Well i really wanted to test out my wireless triggers and flash, but no one had a car ready for me to shoot tonight ;)

Who wants to be my test pig???

So i went here instead..

Sydney City Photoshoot- Quick 15mins session literally due to rain :)

1.

IMG_7343resizesigupload1.jpg

2.

IMG_7359resizesig.jpg

3.

IMG_7346asiguploadborder.jpg

4.

IMG_7342resizesiguploadborder.jpg

5. Yup damn noise :(

IMG_7350.jpg

I got more.. but these will do for now :)

Then on the way home pic :)

Only took a few.. this one turned out ok. not what i was expecting!! but will try again next time.

IMG_7365.jpg

Edited by siddr20
Link to comment
https://www.sau.com.au/forums/topic/266069-tonights-shoot/
Share on other sites

Breath-taking mate...you should be a professional photographer if you are not one already...good work!

Thank so much!! Means a lot hearing these comments :P

Im no professional man.. Hopefully one day i can become one!!

Two more from the night..

IMG_7353resizesig.jpg

IMG_7361resizesig.jpg

Link to comment
https://www.sau.com.au/forums/topic/266069-tonights-shoot/#findComment-4542250
Share on other sites

Thanks slim :P

hmm i was thinking the same, but at 50%-100% view at full res shows the buildings on the bottom perfectly leveled.

I think the bridge just has a slight curve to it.. When you drive on the bridge you go up and then down right?? Like a slight hill so to say?

Link to comment
https://www.sau.com.au/forums/topic/266069-tonights-shoot/#findComment-4542359
Share on other sites

Thank so much!! Means a lot hearing these comments :P

Im no professional man.. Hopefully one day i can become one!!

Two more from the night..

IMG_7353resizesig.jpg

IMG_7361resizesig.jpg

Mate, you got skills...there's no doubt...the way you place your angles etc are breath-taking...mate, there's nothing stopping you doing this part-time as a hobby...shit, I would pay you to take some pictures of my car if you would...

Awesome...not getting paid to say this, just telling you the truth...

Link to comment
https://www.sau.com.au/forums/topic/266069-tonights-shoot/#findComment-4542635
Share on other sites

Mate, you got skills...there's no doubt...the way you place your angles etc are breath-taking...mate, there's nothing stopping you doing this part-time as a hobby...shit, I would pay you to take some pictures of my car if you would...

Awesome...not getting paid to say this, just telling you the truth...

Man that means a lot to me hearing such great feedback!! If it wasn't for people like yourself i wouldn't have the commitment or motivation to keep going!!

So thank you for the kind words!!

I would love to take some pictures of your car but you are in melbourne :down:

Edited by siddr20
Link to comment
https://www.sau.com.au/forums/topic/266069-tonights-shoot/#findComment-4542909
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...