Jump to content
SAU Community

Recommended Posts

hey guy

i was just driving home from the local shops and my engine light come on i have just changed the coils and my

car has no miss fire wat so ever car seems fine but the warning light has come on

has anyone had this problem wat could it be and my engine light is staying on (no flashing).

Link to comment
https://www.sau.com.au/forums/topic/271020-r34-engine-light/
Share on other sites

hey guy

i was just driving home from the local shops and my engine light come on i have just changed the coils and my

car has no miss fire wat so ever car seems fine but the warning light has come on

has anyone had this problem wat could it be and my engine light is staying on (no flashing).

-------------------------------

you've put up several posts now about this but clearly have not taken any previous advice on board - if you had done so by now you would know that you have to jump two pins on the engine diagnostic connector to get the flashing code which tells you what the likely problem is - takes about 1 minute, like I said some time ago - but, hey if its too much trouble to do its best you just keep wildly guessing.........and guessing ..........and posting some more ......lol

  • 2 months later...
hey guy

i was just driving home from the local shops and my engine light come on i have just changed the coils and my

car has no miss fire wat so ever car seems fine but the warning light has come on

has anyone had this problem wat could it be and my engine light is staying on (no flashing).

Engine light on means one of the sensors have failed and giving out an incorrect voltage reading or none at all.

The flashing will only take place when you do a self diagnostics to get the exact sensor code.

Hook up nissan datascan with the cable which you can purchase or take it to nissan for them to hook up the consult.

Free way is do the self diagnostics for the ecu.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...