Jump to content
SAU Community

Recommended Posts

please help az i have no idea were to start??????????? got a wolf waz starting and runing fine, got it tuned last fri, evea since haz been hard to start, now tonite it didnt went threw two batts didnt fire once any ideas were to start wud be much help thanks mind the spelling and stuff i carnt read or rite very well

please help az i have no idea were to start??????????? got a wolf waz starting and runing fine, got it tuned last fri, evea since haz been hard to start, now tonite it didnt went threw two batts didnt fire once any ideas were to start wud be much help thanks mind the spelling and stuff i carnt read or rite very well

-------------------------------

bring it back to the tuner - they obviously may have stuffed something up- get them to look at it

before that, check all wiring and connectors then just in case you have completely flooded the engine - very likely if you have been cranking it forever - the simple fix is do this, get a fully charged battery and put it in then press accelerator all the way to the floor , keep it there, and try to start the motor - keep cranking for at least 20-30 seconds with accelerator all the way down if it begins to fire (roughly at first) then lift back off accelerator and it should start + run (if flooding was the only issue)

-------------------------------

bring it back to the tuner - they obviously may have stuffed something up- get them to look at it

before that, check all wiring and connectors then just in case you have completely flooded the engine - very likely if you have been cranking it forever - the simple fix is do this, get a fully charged battery and put it in then press accelerator all the way to the floor , keep it there, and try to start the motor - keep cranking for at least 20-30 seconds with accelerator all the way down if it begins to fire (roughly at first) then lift back off accelerator and it should start + run (if flooding was the only issue)

cheers, i put new crank sensor, nothing, new air flow,nothing, then spoke to a mate and he said three hours on the dyno and the same plugs a big no no, so tow started it sweet az, leaving the shit plugs in tacking it back to shop to waste some of there time on monday, then guna hit them with, u pack of rip of mutha f**ken thiving dog flamin mongrels. coz they doubled the quote, then probly drop a mean smoker out front and warn everyone off this place for eva, maybe even park my work truck out front for a week with a sign sayn "put lipstick on coz they will f**k you" out front of there shop, thanks for the help

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Initially I thought having a pair of Recaro seats would be a big bonus, it turns out these do get a little uncomfortable on long journeys (my fault, not the seat). I had a look through the GSM Performance website at reclining seats and booked an appointment to visit their show room. I got the Recaro Sportster CS for the R34 from here, was very happy with the service received so of course a re-visit was in order. Unfortunately the two Corbeau seats I had chosen aren't on display but they had 4 other options available. Two seats dug into my back, one dug into my legs and the other was perfect. I also found out that Recaro seats use a larger bolt pattern so some adaption was required. Luckily GSM offer some universal adaptors that should solve this problem. I searched the interwebs for price comparisons and Corbeau themselves were the cheapest at £300 cheaper (for the pair). I asked GSM if they could price match, unfortunately they couldn't. I later received an email saying Corbeau would honour them the same discount, but the purchase was already made. I did however order the brackets from GSM, both arrived on the same day. I started with the passenger side seat, knowing this was going to be a little trial and error. There are 3 mounting holes at the front and 2 at the rear on these JURAN Racing seat rails.  With the adaptor brackets mounted, the allen cap bolts started to push into the seat, NOT GOOD!  The rear mounting holes lined up but there were issues at the front. The holes were 1/2 hole out, so the brackets got a tickle with the drill to modify the holes. The supplied bolts weren't going to be long enough and a spacer was needed to stop the adaptor bars from bending. A local fasteners company supplied be with some nylon spacers and longer bolts (M8x30, although these will be replaced with 35mm long shortly) A before and after I pre-drilled the front bracket before making a start on the driver's seat to save some time. And in no time at all that was in the car too. The all black seats have transformed the interior and these are MUCH more comfortable. The only downside with the new Corbeau seats is I sit a little higher, but I'll happily accept that over discomfort. The Youtube video can be found here: https://www.youtube.com/watch?v=wPyttKPktXA
    • All 3 I guess. The car came with the JASI Aero 4 door Type R Full Kit unpainted so this was one thing at the top of my list to complete then I noticed there were body panels parts for this kit so i picked them up along with some black mesh to fill in the front bumper and front side air vents. car is at a paint and body shop atm completing this work. Next I will be addressing the internal bells and whistles, great summer project I can do with the kids.  full interior removal - ,boys car sound deadening - pads and spray ,boys stereo, sound, lighting - Big 3, GTT or bigger alternator ,kids head lining - dye black add star lighting mod ,daughter. That's it for the next 5-6 months. I have some motor maintenance  work i have to plan out. oil filter relocation, gaskets, mounts. beyond that, mind is starting to turn over if i can use a DET intake plenum, block off turbo ports & pipe in a air intake.      
    • roller coaster of a ride. Alarm system was removed & main harness was repaired where possible. still no fix just random successful starts. moved on to the replacing the ignition switch and relay. well all this troubleshooting & repair has been going on, the car is at a paint and body shop being pushed around. Ive been going down there on odd days after work to get it sorted.     
    • 5th November if you want to come out for a spin wakfield
    • PROBLEM WAS BROKEN COOLANT SENSOR!!! Replaced with a new one and its running mint.
×
×
  • Create New...