Jump to content
SAU Community

Fs Recaro Sr3 And Recaro Rail + 19" Gv2 Chrome Rims + Tyres

coaster

By coaster,
in Classifieds

 Share

Recommended Posts

coaster Proficient

coaster

Posted
Posted (edited)

Item: SR3 Recaro on recaro rail for 33's + others. Drivers seat.

Location: Gold Coast QLD

Item Condition: As new, perfect!

Reason for Selling: Selling Car, parting out.

Price and Payment Conditions: $800 ONO

Extra Info: Seat is mint - come take a look.

Contact Details: 0424506009 or PM

Item:19" Chrome Gestalt Virouge rims with near new tyres 5x114 stud fits ford, nissan, hilux, evo4 onwards etc

Location: Gold Coast

Item Condition: Slight rash on one rim. Can barley notice Rest are perfect

Reason for Selling: selling car and parting out

Price and Payment Conditions: $1900 ono now $1500 ONO with 90-95% rubber!

Pictures: attached - have more if wanted.Contact Details: 0424506009

Edited by coaster
coaster Proficient

coaster

Posted
  • Author
Posted

Rims are sold with the car but the seat is still for sale.

Asking 700 ono with rails - If it doesnt sell soon i may throw it on ebay.

 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nash47
      Cas issue

      By nash47 · Posted

      Did and sync timing with light 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...