Jump to content
SAU Community

Recommended Posts

Street Forced SR20 (S14/S15 Engin) Engine Rebuild. ***NOW Only $5,500***

053fow.jpgdscn0480g.jpgdscn0478f.jpg

The Parts Included In This Build Are As Followed:.

Arias forged pistons 8.5:1 CR

Eagle H beam connecting rods

ARP head stud kit

ARP main stud kit

ARP2000 rod bolts

Cometic metal head gasket

King pro series rod bearings

King pro series mains bearings

Tahho thrust bearings

Nissan Full gasket kit

Nissan water pump

Nissan oil pump

Enduratech timing chain kit

IWIS timing chain

Nissan rocker arms

GKteck rocker arm stoppers

Brian Crower valve springs

Brian Crower titanium retainers

Tomei pon camshafts

Tomei adjustable cam gears

Precision hydraulic lash adjusters

SRC large sump (greddy style)

SRNRG coil pack cover

SRNRG oil filler cap

SRNRG rocker cover (trademark gold)

Machining Done Is As Followed:.

Block cleaned and checked

Block bored and honed

Block tunnel bore and honed

Block resurfaced with timing cover

Crank crack tested and straighten

Crank grind and micro polish

Crank balance

Piston balance

Con rod balance

Clutch cover, flywheel and harmonic balancer balanced

Head clean and check

Head resurfaced

Valve guides k lined

3 angle valve cut

Port and polish on exhaust

RPM limit: 8000

HP rating: 300-480

KW : 220-360kw (Safe)

But could run a good: KW 360-400kw

***************As Per Price must sell this week*************

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Started sifting thru my brakes to decide which ones I will run on Clem   Made me think I should just put them all on Silver...for when brake fade just isn't an option   Should be able to bump rotor up from 343x32 to 348x36 off Supra. Not sure if the Supra annulus is right for the Alcons or APs but trying g to find a used Supra\M4 rotor to test fit The Alcons seem to gain 1-2mm clearance which all helps  
    • So car is getting a few mods to the cage and some jacking points welded in Meantime Ol Silver gets a new gearbox and shiny clutch.  Old Box is being set aside for Clem  
    • Probably speedometer itself if the odometer is ticking. If the needle is stuck from a bit of grease or something that can cause it to stay at 0. Or a cracked solder joint in the speedometer can do it too.
    • Thanks Fella’s   to take this off topic and to elaborate a bit more. I have an rb25/30 going into a r32 GTST.. expected to make around 600-700hp. Would you?   A) R34 GTT box   B) CD00#?  I’ve seen a few posts about the CD swap and sounds fairly involved with making it fit etc but if it’s worth the work then I’ll go that way
    • Lower at the hubs. Funny I forgot to mention that part. Do this pull here I turned the camera off too soon but the graph shows a drop at the top and that was because the pipe from the turbo blew off. The tuner said we could’ve made possibly another 15 whp. He also added if I switched to ethanol we could up the boost some more as well. I was comfortable capping it at the most of 20 pounds. Turns out the turbo pipe just needed a new worm clamp. Got home replaced that then did a third gear pull from 3k to 7200 rpm and the power was great to the top. I just got an ecu mounting bracket from IEE that I need to try and get everything to fit well. It’s a PITA to get the harness and ecu fit properly behind that kick plate 
×
×
  • Create New...