Jump to content
SAU Community

Fs

bradr8

By bradr8,
in For Sale (Private Whole cars only)

 Share

Recommended Posts

bradr8 Rookie

bradr8

Posted
Posted (edited)

Here we have an S13 with a 5 speed manual turbo 1.8l engine. Engine was given a freshen up about 18 months ago with acl rings, bearings and mls headgasket. At the same time all seals, gaskets and clutch kit were done. It has a garrett t28bb turbo which blows no smoke with an intercooler kit and a 3in exhaust with a varex rear muffler. It has also had new radiator and heater hoses and a kit in the clutch slave and master cylinders. Engine has bosch coil conversion and is running 10psi boost there are also sports shockers fitted in the standard struts. Has 17inch speedy wheels with good tread and new brake pads. Inside has a full stereeo system, cruise control, climate control with ac that works, turbo timer, boost gauge. All electrics work fine and there is no rust around the sunroof, has tinted windows and a full alarm system with remote entry. The body has a few minor dents and scratches and the seats have come appart at the stitching but are still comfortable to sit in. Car is driven daily and is serviced every 5000km. Has not missed a beat in the 18months I have had the car on the road. Bought a new project so it has to go. Contact me for more info I am sure there are some small things I have missed. Asking $7500 and located in Murray Bridge SA. 0439379759.

post-67932-1256988388_thumb.jpg

post-67932-1256988407_thumb.jpg

post-67932-1256988424_thumb.jpg

post-67932-1256988440_thumb.jpg

post-67932-1256988459_thumb.jpg

post-67932-1256988475_thumb.jpg

post-67932-1256988497_thumb.jpg

post-67932-1256988511_thumb.jpg

post-67932-1256988529_thumb.jpg

Edited by bradr8
Link to comment
https://www.sau.com.au/forums/topic/294343-fs/
Share on other sites
  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      You Gregged a whole racetrack!?
    • GTSBoy
      R32 GT-R: 4WD Light Turns On After Bumps – Code 19 (ETS Motor) But No Issues Found

      By GTSBoy · Posted

      Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Bireley_32
      R32 GT-R: 4WD Light Turns On After Bumps – Code 19 (ETS Motor) But No Issues Found

      By Bireley_32 · Posted

      Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...