Jump to content
SAU Community

Carparks :(

Submiqent

By Submiqent,
in Western Australia

 Share

Recommended Posts

Submiqent Apprentice

Submiqent

Posted
Posted

Okay so I was in Karrinyup shops and some c$&t reversed into my r34. Dented the front bumper and a little bit of bent metal underneath.

Does anyone know where I can source another bumper and about how much it will cost? Extra points for a rocket propelled grenade launcher and 4wd tracker system -.-

Link to comment
https://www.sau.com.au/forums/topic/297938-carparks/
Share on other sites
Hanaldo Grand Master

Hanaldo

Posted
Posted

Could be a good chance to buy an aftermarket front bar, get kitted up? :)

Seriously though, that sucks, i hate people that do that. Fair enough it might happen some time (if you are fail at driving), but at least leave your details :P

You could try and fix your front bar, doesn't sound too hard. The clips you can get from Repco, and i just used a fiberglass repair kit on mine to fix up the holes. Painting is easy as, i repaired and repainted my front bar and rear bar, looks better than new :D Could you not just bend the metal back around so that it lines up with the hole again? Doesn't have to be perfect, just so it works. Don't know where you could source one of those brackets from...

Link to comment
https://www.sau.com.au/forums/topic/297938-carparks/#findComment-4958774
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Looking for someone with a R34 front bar

      By GTSBoy · Posted

      That looks good, but I think you're going to need much beefier side skirts now.
    • GTSBoy
      Most women will agree that parking is the most taxing part of driving

      By GTSBoy · Posted

      They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • GTSBoy
      new 1.5 LSD issues/concerns

      By GTSBoy · Posted

      I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • GTSBoy
      M35 Brake caliper replacement

      By GTSBoy · Posted

      Define "starting to fail". Wy not just rebuild them?
    • GTSBoy
      S1 rb25/s14 starting problem

      By GTSBoy · Posted

      Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...