Jump to content
SAU Community

Is This The Wrong Exhaust?

R33Matt

By R33Matt,
in Engines & Forced Induction

 Share

Recommended Posts

R33Matt Collaborator

R33Matt

Posted
Posted

The other day I picked up a few people and actually had people in the back of my skyline! lol, Usually I never have anyone in the back. I started to take off and then heard a loud banging sound coming from under the car. The sound was really loud and made the whole car shake! I had a look under my car on the weekend and it looks like the exhaust is against a bar under the car. Looks like the owner before me has put some rubber between the bars to stop them from banging. I was just wondering if the exhaust should be against this bar? It doesn’t look right to me? Is this the wrong exhaust for the R33?

Thanks :)

post-43948-1268187909_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/311380-is-this-the-wrong-exhaust/
Share on other sites
R33Matt Collaborator

R33Matt

Posted
  • Author
Posted

Oh ok, so you think the exhaust is hitting the ground and its not the other bar? That could be it.. but my car is standard height..hmm,

Its HKS Super Dragger exhaust, i would of thought no modification would be needed. To me it looks like the exhaust should be going around that bar, rather than been right up against it. Is it possible this is for a R32 or R34, or does everyone have there exhaust up against that bar?

Ryan180 Enthusiast

Ryan180

Posted
Posted

I had a similar probelm with my car. All you need to do is go to an exhaust shop and they will weld a bracket to the exhaust and then bolt it to the chassis some where.

This will hold the exhaust in place (away from the bar) and stop the vibration

R33Matt Collaborator

R33Matt

Posted
  • Author
Posted (edited)

Thanks for that :) , seems like to fix this i will need to get an exhaust place to bend it or make up that bracket. But does anyone know why this has happened? Did the guy before me order the wrong exhaust, like for the wrong model skyline? Surely they all dont do this... My mate has an exhaust on his skyline and it doesnt even go near that bar, goes around it nicely...

Edited by R33Matt
R33Matt Collaborator

R33Matt

Posted
  • Author
Posted

Just was looking at the type of exhausts you can get, and for HKS you can get it for the R33 GTR or R33 Gts-t, so is it possible the guy before me got the GTR type? and thats why its not fitting 100%?

Ryan180 Enthusiast

Ryan180

Posted
Posted

Not too sure there, I ordered a specific model exhaust to fit my car and i still had the same problem.

Remember not all cars are going to be exactly the same and the manufacture of the exhaust could be out by 1degree at the dump pipe which then magnifies towards the back of the vehicle.

Just my 2cents

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
×
×
  • Create New...