Jump to content
SAU Community

Recommended Posts

SICK OF BEING TARGETED BY MAD KENT COPS OUT TO DEFECT YOU FOR YOU HEKTIC AS f**k S14S ON CHINA CHROMIES?

WANNA LAY WASTE TO TOOLS IN AUTO VX SS'S AND MAKE THERE GIRLFRIEDNS WANNA TAKE YOU TO PROM?

WANNA IMPRESS MATES BY DOING 4TH GEAR HELIS AFTER DOING THE SATURDAY NITE MUNCHIES SERVO RUN?

THEN THIS IS THE F***KING CAR FOR YOU!

sleeper mc sleepy snoozing 1989 s1 mx83 cressida fitted with jzx 81 1jz motor and r154 manual gearbox

MOTOR

f**king 1j. nuff said.

run by haltech e11v2

3 bar map sensor haltech ,haltech boost control

1jz out of jzx81 86,000 klm old

turbosmart rising rate fuel reg

440cc injectors

walbro 255 fuel pump

strengthened and braced t3 single turbo manifold

braided oil feed and drain lines

brand new kkr 560 turbo

trust pod filter

pwr 600x300x75 intercooler , 3'' pipes

battery in boot

alloy radiator with davies craig thermo

50mm external waste gate plumbed back

turbosmart bov hidden under headlight

gates blue timing belt , new tensioner , water pump

os geiken adj exhaust cam gear

3'' straight through exh high flow cat

GEARBOX/clutch

r154 good condition

clutch excedy hyper single ceramic button clutch

custom tailshaft

SUSPENSION

lowered stiffened springs all around

aftermarket shocks

whiteline rear swaybar 16mm

BRAKES, wheels

rays engineering volk rims 17x7.5'' front 17x8.5'' rear, good tyres

r33 front calipers recently recoed

ebc pads

r33 dba gold slotted and drilled rotors

made 205rwkw on 11psi of boost and 700nm of torque

at the moment its making about 270kw on 16-17psi with no sign of detonation or pinging, very safe.

THATS LIKE YOUR MOTHER BEING PUNCHED IN THE OVARIES BY CHUCK NORRIS SO HARD THAT YOU WERENT BORN EVERY TIME IT HITS BOOST

i will include a spare timing belt, a spare garret gt60, a rear set of cressida stockies, the stock cam gear and gear cover, spare set of plugs. aswell as dyno cable and data cable plus software for the haltech.

port macquarie n.s.w

$12,500 (this is friggin cheap)

POSSIBLY OPEN TO TO SWAPS (something sexy or something stupid, nothing in between)

Mitch 0422575362

th_Image033.jpg

th_Image039.jpg

th_Image038.jpg

th_PICT0054.jpg

th_Image037.jpg

th_PICT0056.jpg

My brother-in-law is the person responsible for building this car originally. Put a fair bit of time and effort (and money) into it!!

I can vouch for it being a quick and slightly scary car....

Whoever buys it will have alot of fun in it.

(What happened to all the little non-defect touches?? eg. The pod filter air box, etc.)

My brother-in-law is the person responsible for building this car originally. Put a fair bit of time and effort (and money) into it!!

I can vouch for it being a quick and slightly scary car....

Whoever buys it will have alot of fun in it.

(What happened to all the little non-defect touches?? eg. The pod filter air box, etc.)

car was scary when i got a hold of it, now it has 8 more psi and an actual tune not just a haltech supplied base tune and it friggin hammers

Also it never came with the pod filter shroud? what else is missing? guess he wanted to keep some stuff when he sold it lol?

For every day this is still for sale chuck norrss will kill a puppy, motivated seller here

Someone better call the RSPCA. Theres going to be a lot of dead puppies around here!

ultimate sleeper man....whats it running for the 1/4? always been a fan of the 1j waay more rev happy then its bigger brother. good luck with the sale man

Someone better call the RSPCA. Theres going to be a lot of dead puppies around here!

mate your lucky chuck Norris doesn't hit girls

not sure on qtr mile, I'd probly say it would run a wheelspinning mid 13 at some stupid mph?

Farken hell a few months ago I was looking to sell my 34 4door for one of these........Tomorrow morning im starting to rip her to bits and go all out on it.

I passed up one of these because the guy was too lazy to finish the engineering on it otherwise i would be driving it now lol

Good luck with the sale!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...