Jump to content
SAU Community

Recommended Posts

hey all, im new to this site & skylines

i recently bought a R33 GTS4 paid about 3500 for it.

i was just wondering is there a way to disable the attesa system?

and then simply just plug it in again?

or is this only the R32's?

any feedback would be greatly appreciated:)

thanks

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/
Share on other sites

you cannot just pull out a fuse like in the 32's. this is because their system was electrical and the 33's are hydrological.

You can drain the resovior in the boot but the safest thing to do is take out the front drive shaft.

BTW, how did you manage a 33 gts4 for 3.5k? is it damaged?

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/#findComment-5356095
Share on other sites

The caniser in the boot runs down to the actuator on the O\S\R of the car, it pumps fluids to the transfer case and when the slip light is activated it then runs too the rear diff and is pumped around there aswell, then back too the canister. It does this because it is a high pressured pump that activates clutch packs in the transfer case, this is how the attesa system works. Do not take the fluid out of the clutch packs with be distroid and you will have to spend a lot of money and all the parts with be EX jap.

The fluid is a ATF fluid, at nissan we sell nissan Matic D which is what they used stock.

You can take the front propeller shaft out but thats it.

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/#findComment-5357381
Share on other sites

how would i pull out the shafts? just pull them out

your only taking out the front shaft.

It is located under the car more towards the drivers side next to the gear box area.

there are four bolts that attach it to the car, they are in pricks of a position to get off...

the thing i do is, move one bolt at a time to the best position possible for you to reach by rolling the car, undo it and take it off, roll your car a little back or forward so the next bolt is in the same position and repeat.

when you get good at it, you can have it off in 10-15 mins if that....

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/#findComment-5357421
Share on other sites

As said before.

You can only disconnect the 4wd system in the R32's electronically.

In the 33 and 34 you must remove the front drive shaft.

This is the shaft from your transferbox (the thing hanging off the drivers side of the gearbox) going up to the front diff.

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/#findComment-5359314
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • How much have you lowered?  I had 350Z springs in the rear and was able to pull the camber into factory spec with the factory arms on the rear, obviously the front ran negative camber as it isn't adjustable, but rotating the wheels regularly evened out the wear.
    • Either the installer needs to come back, you need an auto electrician, or you need to learn automotive electricals yourself.   First step Id look at is where that big thing came out of, is there still things unplugged at that location? Maybe they just forgot to put a relay in or something?
    • Well, this is probably where a wiring diagram and a multimeter come into play.
    • I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
×
×
  • Create New...