Jump to content
SAU Community

Recommended Posts

Gday guys,

Have a mate at work that is selling a set of cusco zero 1 coilovers they are good condition, no knocks or leaks.

To suit a R33 skyline. He is asking $900 for the set.

Please contact the person below as i dont know anything about them.

Located in the Adelaide hills SA

Contact Chris on 0420986545

Im selling some of my stuff that is around my place to get my coupe back on the road.

Z32 AFM $250. Good condition mesh isnt bent or damaged.

Early model HR31 S3 GTS grille. Good condition a little plastic polish and it would come up mint. $200

Later model HR31 S3 GTS grille. Same as above. $250

S2 HR31 grille. Good condition. $140

DBA slotted front rotors. Seen less than 15000k. Reason for sale is because i have r33 brakes $200 firm.

R33 engine mounts good condition no cracks. Make an offer

R33 stock dump. Make an offer

RB20 fan blade with viscus - $50. Good condition no cracks etc.

Also have a stock HR31 fuel pump don't know if they are different to Aussie 31's. $30

Stock front and rear swaybars for a HR31. $50 for both

More parts to come in the next few weeks so stay tuned.

All parts are located in the Adelaide hills.

Pics will be up soon.

Pm me or contact me on 0420491344. I work during the day so message would be best.

Adam

  • 2 weeks later...

Added 16/8

2 x s3 rear garnishes.

One comes with a s3 rear garnish, rear number plate lights, boot strip and a set or hotplate taillights in good condition. Chasing $300 firm

other one comes with number plate lights and rear garnish. $200 firm.

TI s3 grill. Good condition chrome isnt cracked. $100

Adam

Edited by KDS_HR31
  • 2 weeks later...

Bump

Got two sets of rear r32 gtst disks, calipers, pads and lines. Both have 80% meat left on every pad, all the disks arent warped or lipped, and calipes dont have split piston seals.

Looking for $300 each set.

Pics soon

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I thought it could be an issue because the standard plate was flexing when stressed. Maybe the original gear set will hold a bit better without flex? Last time on the dyno it made around 670nm at the hubs. Now it have bigger turbo and better intake but have not been on a dyno yet. The car is being used from family trips to drag race events. So the shifts can be a little violent. It is grinding if I shift to fast so was thinking I should overhaul it soon.
    • From the factory on RB26s there's a fitting on the intake manifold collector/"plenum" that provides pre-throttle boost signal. That's how they did it back in the day, I figure it's fine to replicate it.
    • I would be surprised if that wasn't the issue. It's probably telling you, that even if you remove the plastic liner, you may have some other clearance issues that may occur too in some scenarios. IE, tyre to guard. It looks like someone has already rolled the lip, but you may still have issues in the future IE, turning and hitting a bump etc. The fact it changes how bad it makes the noise when you are going backward vs forward is highly indicative that it's the tyre rubbing. They do make a terrible sound, even if you're only pushing a project car that has a liner hanging down on a tyre!   Has the car been lowered? If it has been, what is the measurement from the centre of the wheel hub to the lip of the guard straight up?
    • Summernats cruiser?
    • Mark's a bit smarter than people give him credit... He'd convince the person that is to become dead, to drive him to the forest first. That way his car has no evidence in it, and he's free to dispose of their vehicle permanently how he sees fit too...
×
×
  • Create New...