Jump to content
SAU Community

Recommended Posts

I have a set of gold 5x114.3 only drifteks for sale

3 of them are fine 1 of them is damaged on the inside edge of the wheel, it's been repaired and has recently just randomly started dropping it's air over night

it's a bit of a saga but i could go out tomorrow and get the tyre put back on it and it will hold air for 2 weeks fine then i'll come out one morning and it's dropped all it's air. it's been repaired for like 2 years now, it held air for over a year after i first got it repaired then i took them off the car for a track day and put them back on the car after i came out the next morning and it's dropped it's air.

in all honesty all it really needs is to be taken to a good wheel repairer and they will work where it's been welded a bit better, seriously could just require some sanding and it would be totally fine. <$200

they all have a bit of gutter rash around the edges but nothing bad at all

17 x 8 +35 and 17 x 9 +38 i think, offsets to be 100% confirmed tonight

i will have pics up tonight

Price: $450 - if you factor in say $150 (i highly doubt it would cost that much, it only cost me about $200 to get it repaired in the first place) to get it repaired you get a set of rims for $600 that are in otherwise good condition

the reason i'm not getting them repaired is i took this as an oppotunity/good excuse to get some work wheels :]

0413377833 Northside Brisbane

Edited by mystery_kid
Link to comment
https://www.sau.com.au/forums/topic/336909-gold-drifteks-17/
Share on other sites

drifteks.JPG

bit dusty but you get the idea, they're drifteks

repair.JPG

that's the repair, the inside of it needs to be cleaned up i think and you should be right to go

the black shit is from when i got the tyre put back on they loaded it up with beed sealer and it lasted for 2 weeks and then i came out one morning to the same result

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...