Jump to content
SAU Community

Yamaha 600 Fz6N Fazer

Joe_89

By Joe_89,
in Classifieds

 Share

Recommended Posts

Joe_89 Experienced

Joe_89

Posted
Posted

Hey all,

Not long now untill Im off for a trip to Europe and NEED TO SELL my bike before i leave.

This is a fantastic 600, it has the same engine as a R6 and very comfortable to ride.

The bike is in great condition, has only done 18500kms and is very relible.

Its been always garaged plus it comes with a "Two Brothers" exhaust as well as the old pipes and rego till march 2011

$4,750 ONO

Call Joe, no time wasters please

0406 534 545

5214anf_20.jpeg

486537b_20.jpeg

7453l1h_20.jpeg

39351a_20.jpeg

562079h_20.jpeg

Link to comment
https://www.sau.com.au/forums/topic/351652-yamaha-600-fz6n-fazer/
Share on other sites
  • 2 weeks later...
Joe_89 Experienced

Joe_89

Posted
  • Author
Posted

Hey all,

Getting alot of people call me asking me "whats wrong with it?" "why is it so cheap?"

There is absolutely nothing wrong with it, I had a guy come and see it last week and left a $500 deposit because he realised what a bargain it is, then called a few days later and said he couldnt get the funds together.

So its still for sale, but i leave soon so if it isnt sold by then, its off the market :mellow:

Thanks guys

 Share
Go to topic listing


  • Latest Posts

    • Hendasto
      Lets play a game - What is causing my oil consumption?

      By Hendasto · Posted

      Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • Hendasto
      Are RBs worth building reliability wise

      By Hendasto · Posted

      At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • MBS206
      New kid on the block

      By MBS206 · Posted

      https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...