Jump to content
SAU Community

Recommended Posts

As title states...

I have brand new in box bought several months ago for a project but no longer need,-tomei fuel pressure regulator. Comes with all fittings and stickers in box-never fitted. RRP $275. I'm after $200

Turbosmart supersonic blow off valvue (used) has trumpet on the side that screws on and off to vent to air- can screw this off and screw in piping to allow for plumbback. No longer need this as I have reverted back to my stanard bof with my new setup.many paint them

in black so cops don't get excited over shiny stuff under the bonnet even if plumbbacked- iv left untouched (blue an chrome) RRP $399. I'm after $280

HKS blow off valvue built into piping- I bought this off a friend along with a heap of other stuff. Has been spray painted black to march the piping its sitting on. Trumpet has come off-think iv got it somewhere but it's not essential. Never used it after buying. Probably best to send a photo if anyones interested to make sure it's what your after to suit setup. $$make an offer

can mms photos if required and postage at your cost.

Phone preffered thanks 0419837474

Edited by elir32

Forgot to add..

Turbosmart T piece manual boost controller used for 3 months RRP $85. I'm after $50

brand new timing belt to suit rb25 neo (not sure if it's the same as rb20, 25) aftermarket not genuine Nissan $20

r34 a pillars with factory tweeters 2 small holes drilled in rhs pillar for mounting gauge- otherwise good condition $50 pair

mspec r32 spoiler with brake lamp in undercoat $50

r34 mat set for 4door (missing drivers mat) $80 have a s15 mat I was using instead for drivers.

R34 orange front bar indicators 50$ pair

R33 quarter panel indicators orange 20$ pair

R33 quarter panels $100 each

R33 diff $100

r33 steering rack assembly complete minus lower control arms $150

have various other 33 bits-check my previous topics first as only few bits left

  • 4 weeks later...
  • 2 weeks later...
  • 2 weeks later...

few pics of bovs and fpr

seem to have misplaced turbosmart t piece so thats no longer available

post-60709-0-29731700-1302309553_thumb.png

post-60709-0-11140900-1302309581_thumb.png

post-60709-0-12114200-1302309627_thumb.png

post-60709-0-81293000-1302309724_thumb.png

post-60709-0-60015400-1302309975_thumb.jpg

post-60709-0-19706100-1302310317_thumb.jpg

  • 2 months later...

bump $150 for fpr

$250 for Turbosmart Bloww off valvue

r33 front gaurds $100 pair

r33 heater unit working $100

offers on rest

  • 1 month later...

Bump..

Steering rack gone

Floor mars gone

Only one quarter panel left,

Brand new fpr anyone?150$ over 100$ cheaper than buying off the shelf for the same thing lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...