Jump to content
SAU Community

Floor-Handbrake Adjustment?

Ben-88
 Share

Recommended Posts

Ben-88 Apprentice

Ben-88

Posted
Posted

Well i know normally when you have the handbreak in the centre it can be adjusted at the base of where the handle is to reduce the distance the lever travels till its at full lock. The issue i have is when i push the floor-hand brake on my auto to a normal sort of level if youre on an incline it doesnt do much, so its relying on the park gear to stop it rolling away. If however i push it overly firm and its virtually inline with the foot rest at this point then it is enough to stop it rolling. So i was wondering if anyone knows where the adjustment is located so that it doesnt need to be pressed in as far to engage fully? If anyone has seen a DIY on how to get to the adjustment point then a link would be much appreciated.

Link to comment
https://www.sau.com.au/forums/topic/366238-floor-handbrake-adjustment/
Share on other sites
j_coote Rookie

j_coote

Posted
Posted

There is a DIY for this on www.g35driver.com, it is for a manual but it's virtually the same for the autos. Just that the adjuster that is normally beside the 'hand' brake is under the dash beside the 'foot' brake for autos. I did mine, took no time at all and now it works much better.

Ben-88 Apprentice

Ben-88

Posted
  • Author
Posted

easily found the adjustment bolt at the top of the pedal... a couple turns and it was tight enough. I didnt bother doing the adjustment from behind the rear wheel as i got enough out of the one near the pedal. Was even easier than a normal hand break cause i didnt have to even remove any interior panels, was seriousley a 2min job... and that includes getting the tools out.

..350GT8.. Enthusiast

..350GT8..

Posted
Posted

You can also actually adjust the park brakes shoes.. You may or may not know that v35 run a park brake setup where it has like drum brake setup which is in the inside o the rear rotors.. If u take your back wheels off u will see on the around the center of your rear rotor that there is a rubber grommets or plug.. Remove it then turn the rotor with park brake off.. Whilst turning get a torch and peep theru that hole u will see a sprocket looking mechanism.. Turning it will tighten or loosen your park brakes.. From memory it's located towards top of the rotor.. General rule is to tighten it to point where it locks up ad u can't turn the rotor and back off about 3 turns..

  • 2 weeks later...
  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • dyl33
      VOLK RACING GTC CENTRE CAPS

      By dyl33 · Posted

      Centre caps $250
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Duncan
      Boost cut after swap(RB25DET NEO) R34

      By Duncan · Posted

      Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...